Hello,
I am doing my graduate project using Dragon 12 Plus kit. I have written C
Progrm in codewarrior for my project. I got error like TMSK1 is not declared.
should I need to use any header file for staus register?
It would most if anybody explain how to load program into 68hcs12
microcontroller with codewarrior?
Thanking you,
Narendra
Error in c program / Dragon 12 plus /68hcs12
Started by ●April 28, 2010
Reply by ●May 1, 20102010-05-01
Hi thanks for reply,
I am using serial port close to LCD. I am here attached with error screenshot. I have tested with COM and USB port (in serial monitor mode)but not able to communicate. your help would be most appreciated.
Thanks
________________________________
From: Dumitru 58
To: narendra pipaliya
Sent: Thu, 29 April, 2010 2:37:46 PM
Subject: Re: Error in c program / Dragon 12 plus /68hcs12
which serial port on the dragonboard are you using to download your program to it? the one by the LCD or the one below by the power jack?
you should be using the one close to the LCD
________________________________
From: narendra pipaliya
To: urtimud_jr
Sent: Wed, April 28, 2010 10:21:29 AM
Subject: Re: Error in c program / Dragon 12 plus /68hcs12
yes it is installed on dragonbord. i had tried to connect through rs232, but i got error like no hadware connection found. COM port is working fine in my laptop. I am not able to set serial monitor connection.
________________________________
From: urtimud_jr
To: narendra pipaliya
Sent: Wed, 28 April, 2010 12:04:08 AM
Subject: Re: Error in c program / Dragon 12 plus /68hcs12
Do you have the serial monitor installed on the Dragonboard?
--- In 6..., narendra pipaliya wrote:
>
> Hello,
> I am doing my graduate project using Dragon 12 Plus kit. I have written C Progrm in codewarrior for my project. I got error like TMSK1 is not declared. should I need to use any header file for staus register?
> It would most if anybody explain how to load program into 68hcs12 microcontroller with codewarrior?
>
> Thanking you,
> Narendra
>
>
>
I am using serial port close to LCD. I am here attached with error screenshot. I have tested with COM and USB port (in serial monitor mode)but not able to communicate. your help would be most appreciated.
Thanks
________________________________
From: Dumitru 58
To: narendra pipaliya
Sent: Thu, 29 April, 2010 2:37:46 PM
Subject: Re: Error in c program / Dragon 12 plus /68hcs12
which serial port on the dragonboard are you using to download your program to it? the one by the LCD or the one below by the power jack?
you should be using the one close to the LCD
________________________________
From: narendra pipaliya
To: urtimud_jr
Sent: Wed, April 28, 2010 10:21:29 AM
Subject: Re: Error in c program / Dragon 12 plus /68hcs12
yes it is installed on dragonbord. i had tried to connect through rs232, but i got error like no hadware connection found. COM port is working fine in my laptop. I am not able to set serial monitor connection.
________________________________
From: urtimud_jr
To: narendra pipaliya
Sent: Wed, 28 April, 2010 12:04:08 AM
Subject: Re: Error in c program / Dragon 12 plus /68hcs12
Do you have the serial monitor installed on the Dragonboard?
--- In 6..., narendra pipaliya wrote:
>
> Hello,
> I am doing my graduate project using Dragon 12 Plus kit. I have written C Progrm in codewarrior for my project. I got error like TMSK1 is not declared. should I need to use any header file for staus register?
> It would most if anybody explain how to load program into 68hcs12 microcontroller with codewarrior?
>
> Thanking you,
> Narendra
>
>
>
