MC9S12A256B vs MC9S12DP256B (and CodeWarrior)

Started by varneybob January 23, 2003
I'm using CodeWarrior for HC(S)12. We've been using an eval board
with the MC9S12DP256B MCU, but are actual MCU is the MC9S12A256B. I
cannot get CodeWarrior to talk to the MCU via the P&E BDM Multilink
cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-ID
drop-down list (it _does_ list the MC9S12DP256B).

Any help would be appreciated!



I had the same problem like you have. After
troubleshooting, I have found out that the PLL circuit
was not installed on my 9S12A256 bread board. When I
switch to use the external clock, it worked fine.

Wayne
--- "varneybob <>"
<> wrote:
> I'm using CodeWarrior for HC(S)12. We've been using
> an eval board
> with the MC9S12DP256B MCU, but are actual MCU is the
> MC9S12A256B. I
> cannot get CodeWarrior to talk to the MCU via the
> P&E BDM Multilink
> cable. Also CodeWarrior, does not list the
> MC9S12A256B in a MCU-ID
> drop-down list (it _does_ list the MC9S12DP256B).
>
> Any help would be appreciated!


__________________________________________________



varneybob,

If you are still on the base V1.2 install, you need to upgrade a bunch
of files (headers, P&E driver, more) - contact metrowerks.
I went through the same thing on an A series part. They just aren't
supported in off the 1.2 CD install.

-zathra_70

--- In , "varneybob <varneybob@y...>"
<varneybob@y...> wrote:
> I'm using CodeWarrior for HC(S)12. We've been using an eval board
> with the MC9S12DP256B MCU, but are actual MCU is the MC9S12A256B. I
> cannot get CodeWarrior to talk to the MCU via the P&E BDM Multilink
> cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-ID
> drop-down list (it _does_ list the MC9S12DP256B).
>
> Any help would be appreciated!





Access to these update files would be much appreciated.

B.K.

>>> 01/22/03 07:45PM >>>
varneybob,

If you are still on the base V1.2 install, you need to upgrade a bunch
of files (headers, P&E driver, more) - contact metrowerks.
I went through the same thing on an A series part. They just aren't
supported in off the 1.2 CD install.

-zathra_70

--- In , "varneybob <varneybob@y...>"
<varneybob@y...> wrote:
> I'm using CodeWarrior for HC(S)12. We've been using an eval board
> with the MC9S12DP256B MCU, but are actual MCU is the MC9S12A256B. I
> cannot get CodeWarrior to talk to the MCU via the P&E BDM Multilink
> cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-ID
> drop-down list (it _does_ list the MC9S12DP256B).
>
> Any help would be appreciated!


--------------------
">http://docs.yahoo.com/info/terms/ *************************************************************************
IMPORTANT: This email message is for the sole use of the intended
recipient(s) and may contain confidential and privileged information.
Any unauthorized review, use, disclosure or distribution is prohibited.
If you are not the intended recipient, please contact the sender by
reply email and destroy all copies of the original message. Please
advise immediately if you or your employer do not consent to Internet
email for messages of this kind. Opinions, conclusions and other
information contained in this e-mail message that do not relate to the
official business of Life Fitness shall be understood as neither given
nor endorsed by it.
*************************************************************************


I've emailed Metrowerks but have not heard back yet. Is there any
way you can post all the necessary files somewhere?

--- In , "zathra_70 <zathra_70@y...>"
<zathra_70@y...> wrote:
> varneybob,
>
> If you are still on the base V1.2 install, you need to upgrade a
bunch
> of files (headers, P&E driver, more) - contact metrowerks.
> I went through the same thing on an A series part. They just aren't
> supported in off the 1.2 CD install.
>
> -zathra_70
>
> --- In , "varneybob <varneybob@y...>"
> <varneybob@y...> wrote:
> > I'm using CodeWarrior for HC(S)12. We've been using an eval
board
> > with the MC9S12DP256B MCU, but are actual MCU is the
MC9S12A256B. I
> > cannot get CodeWarrior to talk to the MCU via the P&E BDM
Multilink
> > cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-
ID
> > drop-down list (it _does_ list the MC9S12DP256B).
> >
> > Any help would be appreciated!





Actually I just programmed the MC9S12A256B part with the MC9S12DP256B
settings from CodeWarrior V1.2! We found out that the MCU was being
held in reset because of a fault on our text fixture. Everything is
going smooth for the moment.

And as a side note, the Metrowerks website has a little blurb that
CodeWarrior 2.0 for HC(S)12 is available for download, but darn if I
could find it anywhere.

Thanks.

--- In , "varneybob <varneybob@y...>"
<varneybob@y...> wrote:
> I've emailed Metrowerks but have not heard back yet. Is there any
> way you can post all the necessary files somewhere?
>
> --- In , "zathra_70 <zathra_70@y...>"
> <zathra_70@y...> wrote:
> > varneybob,
> >
> > If you are still on the base V1.2 install, you need to upgrade a
> bunch
> > of files (headers, P&E driver, more) - contact metrowerks.
> > I went through the same thing on an A series part. They just
aren't
> > supported in off the 1.2 CD install.
> >
> > -zathra_70
> >
> > --- In , "varneybob <varneybob@y...>"
> > <varneybob@y...> wrote:
> > > I'm using CodeWarrior for HC(S)12. We've been using an eval
> board
> > > with the MC9S12DP256B MCU, but are actual MCU is the
> MC9S12A256B. I
> > > cannot get CodeWarrior to talk to the MCU via the P&E BDM
> Multilink
> > > cable. Also CodeWarrior, does not list the MC9S12A256B in a
MCU-
> ID
> > > drop-down list (it _does_ list the MC9S12DP256B).
> > >
> > > Any help would be appreciated!




ftp.metrowerks.com/pub/embedded/HC12/CW12_V2_0.exe
But this is the full installation: 134MB

Erich

> -----Original Message-----
> From: varneybob <> [mailto:]
> Sent: Donnerstag, 23. Januar 2003 14:14
> To:
> Subject: [68HC12] Re: MC9S12A256B vs MC9S12DP256B (and CodeWarrior) > I've emailed Metrowerks but have not heard back yet. Is there any
> way you can post all the necessary files somewhere?
>
> --- In , "zathra_70 <zathra_70@y...>"
> <zathra_70@y...> wrote:
> > varneybob,
> >
> > If you are still on the base V1.2 install, you need to upgrade a
> bunch
> > of files (headers, P&E driver, more) - contact metrowerks.
> > I went through the same thing on an A series part. They just aren't
> > supported in off the 1.2 CD install.
> >
> > -zathra_70
> >
> > --- In , "varneybob <varneybob@y...>"
> > <varneybob@y...> wrote:
> > > I'm using CodeWarrior for HC(S)12. We've been using an eval
> board
> > > with the MC9S12DP256B MCU, but are actual MCU is the
> MC9S12A256B. I
> > > cannot get CodeWarrior to talk to the MCU via the P&E BDM
> Multilink
> > > cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-
> ID
> > > drop-down list (it _does_ list the MC9S12DP256B).
> > >
> > > Any help would be appreciated! > -------------------- >
> ">http://docs.yahoo.com/info/terms/ >



Erich,
I first got an error on transfer now a file not found error while trying to download the update.

Is it still available?

thanks
ed
--
At 03:54 PM 1/23/2003 +0100, you wrote:
>ftp.metrowerks.com/pub/embedded/HC12/CW12_V2_0.exe
>But this is the full installation: 134MB
>
>Erich
>
> > -----Original Message-----
> > From: varneybob <> [mailto:]
> > Sent: Donnerstag, 23. Januar 2003 14:14
> > To:
> > Subject: [68HC12] Re: MC9S12A256B vs MC9S12DP256B (and CodeWarrior)
> >
> >
> > I've emailed Metrowerks but have not heard back yet. Is there any
> > way you can post all the necessary files somewhere?
> >
> > --- In , "zathra_70 <zathra_70@y...>"
> > <zathra_70@y...> wrote:
> > > varneybob,
> > >
> > > If you are still on the base V1.2 install, you need to upgrade a
> > bunch
> > > of files (headers, P&E driver, more) - contact metrowerks.
> > > I went through the same thing on an A series part. They just aren't
> > > supported in off the 1.2 CD install.
> > >
> > > -zathra_70
> > >
> > > --- In , "varneybob <varneybob@y...>"
> > > <varneybob@y...> wrote:
> > > > I'm using CodeWarrior for HC(S)12. We've been using an eval
> > board
> > > > with the MC9S12DP256B MCU, but are actual MCU is the
> > MC9S12A256B. I
> > > > cannot get CodeWarrior to talk to the MCU via the P&E BDM
> > Multilink
> > > > cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-
> > ID
> > > > drop-down list (it _does_ list the MC9S12DP256B).
> > > >
> > > > Any help would be appreciated!
> >
> >
> > --------------------
> >
> >
> >
> > ">http://docs.yahoo.com/info/terms/
> >
> >
> >
>-------------------- >
>">http://docs.yahoo.com/info/terms/
>





Hmm, seems that the web team is moving files around :-(
Let me check.

Erich

> -----Original Message-----
> From: Ed Carryer [mailto:]
> Sent: Donnerstag, 23. Januar 2003 19:12
> To:
> Subject: RE: [68HC12] Re: MC9S12A256B vs MC9S12DP256B (and CodeWarrior) > Erich,
> I first got an error on transfer now a file not found error while
> trying to download the update.
>
> Is it still available?
>
> thanks
> ed
> --
> At 03:54 PM 1/23/2003 +0100, you wrote:
> >ftp.metrowerks.com/pub/embedded/HC12/CW12_V2_0.exe
> >But this is the full installation: 134MB
> >
> >Erich
> >
> > > -----Original Message-----
> > > From: varneybob <> [mailto:]
> > > Sent: Donnerstag, 23. Januar 2003 14:14
> > > To:
> > > Subject: [68HC12] Re: MC9S12A256B vs MC9S12DP256B (and CodeWarrior)
> > >
> > >
> > > I've emailed Metrowerks but have not heard back yet. Is there any
> > > way you can post all the necessary files somewhere?
> > >
> > > --- In , "zathra_70 <zathra_70@y...>"
> > > <zathra_70@y...> wrote:
> > > > varneybob,
> > > >
> > > > If you are still on the base V1.2 install, you need to upgrade a
> > > bunch
> > > > of files (headers, P&E driver, more) - contact metrowerks.
> > > > I went through the same thing on an A series part. They just aren't
> > > > supported in off the 1.2 CD install.
> > > >
> > > > -zathra_70
> > > >
> > > > --- In , "varneybob <varneybob@y...>"
> > > > <varneybob@y...> wrote:
> > > > > I'm using CodeWarrior for HC(S)12. We've been using an eval
> > > board
> > > > > with the MC9S12DP256B MCU, but are actual MCU is the
> > > MC9S12A256B. I
> > > > > cannot get CodeWarrior to talk to the MCU via the P&E BDM
> > > Multilink
> > > > > cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-
> > > ID
> > > > > drop-down list (it _does_ list the MC9S12DP256B).
> > > > >
> > > > > Any help would be appreciated!
> > >
> > >
> > > --------------------
> > >
> > >
> > >
> > > ">http://docs.yahoo.com/info/terms/
> >
> >
> >
>-------------------- >
>">http://docs.yahoo.com/info/terms/
>


--------------------
">http://docs.yahoo.com/info/terms/


http://www.metrowerks.com/MW/Develop/Embedded/HC12/Default.htm
download link on the right side.

Or:
http://www.metrowerks.com/mw/download/default.htm?did=find&vers=CWHC12&submi
t=Find

Erich

> -----Original Message-----
> From: Ed Carryer [mailto:]
> Sent: Donnerstag, 23. Januar 2003 19:12
> To:
> Subject: RE: [68HC12] Re: MC9S12A256B vs MC9S12DP256B (and CodeWarrior) > Erich,
> I first got an error on transfer now a file not found error while
> trying to download the update.
>
> Is it still available?
>
> thanks
> ed
> --
> At 03:54 PM 1/23/2003 +0100, you wrote:
> >ftp.metrowerks.com/pub/embedded/HC12/CW12_V2_0.exe
> >But this is the full installation: 134MB
> >
> >Erich
> >
> > > -----Original Message-----
> > > From: varneybob <> [mailto:]
> > > Sent: Donnerstag, 23. Januar 2003 14:14
> > > To:
> > > Subject: [68HC12] Re: MC9S12A256B vs MC9S12DP256B (and CodeWarrior)
> > >
> > >
> > > I've emailed Metrowerks but have not heard back yet. Is there any
> > > way you can post all the necessary files somewhere?
> > >
> > > --- In , "zathra_70 <zathra_70@y...>"
> > > <zathra_70@y...> wrote:
> > > > varneybob,
> > > >
> > > > If you are still on the base V1.2 install, you need to upgrade a
> > > bunch
> > > > of files (headers, P&E driver, more) - contact metrowerks.
> > > > I went through the same thing on an A series part. They just aren't
> > > > supported in off the 1.2 CD install.
> > > >
> > > > -zathra_70
> > > >
> > > > --- In , "varneybob <varneybob@y...>"
> > > > <varneybob@y...> wrote:
> > > > > I'm using CodeWarrior for HC(S)12. We've been using an eval
> > > board
> > > > > with the MC9S12DP256B MCU, but are actual MCU is the
> > > MC9S12A256B. I
> > > > > cannot get CodeWarrior to talk to the MCU via the P&E BDM
> > > Multilink
> > > > > cable. Also CodeWarrior, does not list the MC9S12A256B in a MCU-
> > > ID
> > > > > drop-down list (it _does_ list the MC9S12DP256B).
> > > > >
> > > > > Any help would be appreciated!
> > >
> > >
> > > --------------------
> > >
> > >
> > >
> > > ">http://docs.yahoo.com/info/terms/
> >
> >
> >
>-------------------- >
>">http://docs.yahoo.com/info/terms/
>


--------------------
">http://docs.yahoo.com/info/terms/