Codewarrior and Motorola SDI, BDM port

Started by a2vutuan February 11, 2004
Hi,
I'm using M68HC912B32EVB. I've been trying to use Motorola SDI as an
interface between my EVB and Codewarrior. But the Codewarrior
Dubugger can't detect my EVB. It keeps on saying that "Target not
ready or not connected on COM2" when I do "Set Target".
My connection is like this:
[COM2 of PC] -> SDI -> [BDM port of EVB].
I also installed a jumper on the pin 3,4 of J51 of the SDI as
instructed in the manual, this is to use standard supply for the
SDI. And mine is Codewarrior Studio Special Edition only.
I've seen that lots of people can use BDM port, hopefully you can
have me out of this. Thanks alot.
VT



Hello,
I have the same problem with M68HC912C32EVB.. Buy a BDM ...
Regards
cosming

----- Original Message -----
From: a2vutuan
To:
Sent: Wednesday, February 11, 2004 6:49 PM
Subject: [68HC12] Codewarrior and Motorola SDI, BDM port Hi,
I'm using M68HC912B32EVB. I've been trying to use Motorola SDI as an
interface between my EVB and Codewarrior. But the Codewarrior
Dubugger can't detect my EVB. It keeps on saying that "Target not
ready or not connected on COM2" when I do "Set Target".
My connection is like this:
[COM2 of PC] -> SDI -> [BDM port of EVB].
I also installed a jumper on the pin 3,4 of J51 of the SDI as
instructed in the manual, this is to use standard supply for the
SDI. And mine is Codewarrior Studio Special Edition only.
I've seen that lots of people can use BDM port, hopefully you can
have me out of this. Thanks alot.
VT
--------------------To learn more about Motorola Microcontrollers, please visit
http://www.motorola.com/mcu
o learn more about Motorola Microcontrollers, please visit
http://www.motorola.com/mcu

------
Yahoo! Groups Links

a.. To




Hi Cosmin,
It's great u also experienced this. Could u tell me abit more how u
overcomed this? What do u mean by saying Buy a BDM? Look forward to
ur reply,
Tuan, --- In , "Cosmin Giurgiu" <cosmingiurgiu@h...>
wrote:
> Hello,
> I have the same problem with M68HC912C32EVB.. Buy a BDM ...
> Regards
> cosming
>
> ----- Original Message -----
> From: a2vutuan
> To:
> Sent: Wednesday, February 11, 2004 6:49 PM
> Subject: [68HC12] Codewarrior and Motorola SDI, BDM port > Hi,
> I'm using M68HC912B32EVB. I've been trying to use Motorola SDI
as an
> interface between my EVB and Codewarrior. But the Codewarrior
> Dubugger can't detect my EVB. It keeps on saying that "Target
not
> ready or not connected on COM2" when I do "Set Target".
> My connection is like this:
> [COM2 of PC] -> SDI -> [BDM port of EVB].
> I also installed a jumper on the pin 3,4 of J51 of the SDI as
> instructed in the manual, this is to use standard supply for the
> SDI. And mine is Codewarrior Studio Special Edition only.
> I've seen that lots of people can use BDM port, hopefully you
can
> have me out of this. Thanks alot.
> VT
>