Forums

X6809.EXE (Macro Assembler by 2500 AD) Documentation

Started by ckrusen August 12, 2010
I need the documentation for 2500 AD's Macro Assembler X6809

Running X6809 with no command line options yields:

c:\asmb09>x6809
                   6809 Macro Assembler   -   Version 4.02a
                Copyright (C) 1985 by 2500 A.D. Software, Inc.

Listing Destination  (N, T, D, E, L, P, <CR> = N) : n

I then press Ctrl+C and the program exits.

At a minimum I need the command line options.

Any help would be greatly appreciated.

P.S. documentation for the utilities LINK09.exe and HEX.exe (also ver 4.02a
by 2500 AD) would be helpful to!

	   
					
---------------------------------------		
Posted through http://www.EmbeddedRelated.com
On Aug 12, 8:13=A0am, "ckrusen" <ckrusen@n_o_s_p_a_m.comcast.net> wrote:
> I need the documentation for 2500 AD's Macro Assembler X6809 > > Running X6809 with no command line options yields: > > c:\asmb09>x6809 > =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A06809 Macro Assembler =A0 - =A0 Ver=
sion 4.02a
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 Copyright (C) 1985 by 2500 A.D. Software,=
Inc.
> > Listing Destination =A0(N, T, D, E, L, P, <CR> =3D N) : n > > I then press Ctrl+C and the program exits. > > At a minimum I need the command line options. > > Any help would be greatly appreciated. > > P.S. documentation for the utilities LINK09.exe and HEX.exe (also ver 4.0=
2a
> by 2500 AD) would be helpful to! > > --------------------------------------- =A0 =A0 =A0 =A0 > Posted throughhttp://www.EmbeddedRelated.com
try googling 2500ad I am pretty sure the documentation is similar for all target devices ftp://ftp.prenhall.com/pub/esm/electrical_and_computer_engineering.s-045/mi= ller/2500AD.pdf Dave
On Aug 12, 1:13=A0pm, "ckrusen" <ckrusen@n_o_s_p_a_m.comcast.net> wrote:
> I need the documentation for 2500 AD's Macro Assembler X6809 > > Running X6809 with no command line options yields: > > c:\asmb09>x6809 > =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A06809 Macro Assembler =A0 - =A0 Ver=
sion 4.02a
> =A0 =A0 =A0 =A0 =A0 =A0 =A0 =A0 Copyright (C) 1985 by 2500 A.D. Software,=
Inc.
> > Listing Destination =A0(N, T, D, E, L, P, <CR> =3D N) : n > > I then press Ctrl+C and the program exits. > > At a minimum I need the command line options. > > Any help would be greatly appreciated. > > P.S. documentation for the utilities LINK09.exe and HEX.exe (also ver 4.0=
2a
> by 2500 AD) would be helpful to! > > --------------------------------------- =A0 =A0 =A0 =A0 > Posted throughhttp://www.EmbeddedRelated.com
None,Terminal,Printer,Disk,Error only,List on/off. Select an option and follow the prompts. Or use the command line option x6809 [-q] input_filename [output_filename] [-t, -p, -px, -d, -dx, -d,drive:, -d,\dir\, -et, - ep, -ede, -lt, -lp, -ld] anything inside brackets are optional, dont type the brackets.