Kernel hangs after the control is transferred U-Boot 1.1.3 (ppc83xx-20050315-dev) (Jun 29 2006 - 16:33:51) MPC83XX *** THIS IS AN ALPHA VERSION OF UBOOT FOR 8325 *** Clock configuration: Coherent System Bus: 132 MHz Core: 264 MHz QE: 99 MHz Local Bus Controller: 132 MHz Local Bus: 16 MHz DDR: 264 MHz I2C: 132 MHz CPU: MPC83xx, Rev: 10 at 264 MHz Board: Freescale MPC832XEPB I2C: ready DRAM: DDR:clk_cntl =3D 02000000 DDR:csbnds[0] =3D 00000003 DDR:cs_config[0] =3D 80c40101 DDR:iming_cfg_0 =3D 00220802 DDR:iming_cfg_1 =3D 26256222 DDR:timing_cfg_2 =3D 0f9028c7 DDR:timing_cfg_3 =3D 00000000 DDR:sdram_cfg =3D 43080000 DDR:sdram_cfg2 =3D 00401000 DDR:sdram_mode =3D 44400232 DDR:sdram_mode2 =3D 8000c000 DDR:sdram_interval =3D 03200064 DDR:sdram_cfg =3D c3080000 SDRAM on Local Bus is NOT available! DDR RAM: 64 MB len =3D 0x50350 , monitor base =3D 0xff800000 env_flash.c, SECOND env_init() - Step 1, env_ptr->data =3D 0xff850004 env_flash.c, env_init(), env_ptr->data =3D0xff850004 CFG_SDRAM_BASE =3D 0x0 , gd->ram_size =3D 0x4000000, addr =3D 0x4000000 Top of RAM usable for U-Boot at: 04000000 Reserving 320k for U-Boot at: 03faf000 Reserving 8193k for malloc() at: 037aec00 addr =3D 0x3faf000 , TOTAL_MALLOC_LEN =3D 0x800400 Reserving 76 Bytes for Board Info at: 037aebb4 Reserving 400 Bytes for Global Data at: 037aea24 Stack Pointer at: 037aea08 New Stack Pointer is: 037aea08 board.c, board_init_f() - Step 2 Now running in RAM - U-Boot at: 03faf000 FLASH: 512 kB env_common.c, env_relocate() - Step1 env_common.c, env_relocate() - Step2, env_common.c, env_relocate() - Step3 env_common.c, env_relocate() - Step4 - default env: ptr =3D 67062152, env_ptr =3D 58387464 ptr =3D 0x3ff4988, env_ptr =3D 0x37aec08 Env_Flash_Addr_Partha =3D 0xff845988 env_common.c, env_relocate() - Step5- env_crc_update() env_common.c, env_relocate() - Step7 - gd->env_addr =3D 58387468 , 0x37aec0c PCI1 32bit on PMC1 & PMC2 & PMC3 PCI Scan: Found Bus 0, Device 16, Function 0 In: serial Out: serial Err: serial U-Boot relocated to 03faf000 Net: FSL GETH0, FSL GETH1 ### main_loop entered: bootdelay=3D6 ### main_loop: bootcmd=3D"setenv bootargs root=3D/dev/ram rw console=3D$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;bootm $loadaddr $ramdiskaddr" Hit any key to stop autoboot: 6 5 4 3 2 1 0 Trying FSL GETH0 .Auto negotiating done duplexity: full mac speed set to: 100 Using FSL GETH0 device TFTP from server 192.168.0.83; our IP address is 192.168.0.56 Filename 'ramdisk'. Load address: 0x400000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################## done Bytes transferred =3D 2750544 (29f850 hex) Trying FSL GETH0 Using FSL GETH0 device TFTP from server 192.168.0.83; our IP address is 192.168.0.56 Filename 'uImage'. Load address: 0x200000 Loading: *################################################################# ################################################################# ################################################################# ########## done Bytes transferred =3D 1045614 (ff46e hex) ## Booting image at 00200000 ... Image Name: Linux-2.6.11 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1045550 Bytes =3D 1021 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Current stack ends at 0x037AE6B0 =3D> set upper limit to 0x00800000 ## cmdline at 0x007FFF00 ... 0x007FFF25 bd address =3D 0x037AEBB4 memstart =3D 0x00000000 memsize =3D 0x04000000 flashstart =3D 0xFF800000 flashsize =3D 0x00080000 flashoffset =3D 0x00049000 sramstart =3D 0x00000000 sramsize =3D 0x00000000 bootflags =3D 0x00000001 intfreq =3D 264 MHz busfreq =3D 132 MHz ethaddr =3D 00:04:9F:00:00:00 eth1addr =3D 00:04:9F:00:00:01 IP addr =3D 192.168.0.56 baudrate =3D 115200 bps ## Loading RAMDisk Image at 00400000 ... Image Name: uboot ext2 ramdisk rootfs Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 2750480 Bytes =3D 2.6 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## initrd at 0x00400040 ... 0x0069F84F (len=3D2750480=3D0x29F810) Loading Ramdisk to 0350e000, end 037ad810 ... OK ## Transferring control to Linux (at address 00000000) ...
Transferring control to Linux (at address 00000000) ... kernel hangs
Started by ●June 29, 2006