Forums

H-JTAG

Started by Fernando Barboza March 18, 2007
Hello all!

I have tried to use Keil (V.3.03) with H-JTAG server (V.0.43)
and Wiggler, but I didn't have success.

When I start debug mode in Keil, my Target (MCB2100) don't is
update with new software. The software is starting and breakpoint don't
function properly.

I made my JTAG according the site H-JTAG.

Can somebody help me?

Thanks!

Fernando

Santa Catarina - Brazil.

An Engineer's Guide to the LPC2100 Series

-> i like to know whether your h-jtag display the device id ?
if Yes then please verify following things...

-> Verify that MAM is disabled, because JTAG is not aware of MAM which
cause strange problems.
-> I am also using h-jtag with 2103 & 2104 on keil & it's working
propery
-> please send more detailed info...
-> i like to know whether your h-jtag display the device id ?
if Yes then please verify following things...

Yes, The H-Jtag display "ARM7TDMI-S" "0x4F1F0F0F".
-> Verify that MAM is disabled, because JTAG is not aware of MAM which
cause strange problems.

It was set, but with disable, happened problem also.
-> I am also using h-jtag with 2103 & 2104 on keil & it's working
propery

-> please send more detailed info...

I have receive in Command Window, when I start debug mode.

RDI-Error 5: RDIError_DataAbort

Load "C:\\Keil\\ARM\\RV30\\Boards\\Keil\\MCB2100\\Blinky\\Flash\\Blinky.AXF"
RDI-Error 5: RDIError_DataAbort

RDI-Error 5: RDIError_DataAbort

RDI-Error 5: RDIError_DataAbort

RDI-Error 5: RDIError_DataAbort

*** RDI: System-Reset is not supported !

BS \Blinky\61

BS \Blinky\36

I have receive in Command Window, when I try load code.

*** RDI: System-Reset is not supported !

RDI-Error 5: RDIError_DataAbort

RDI-Error 5: RDIError_DataAbort

RDI-Error 5: RDIError_DataAbort

RDI-Error 5: RDIError_DataAbort

*** RDI: System-Reset is not supported !

Now, when I Check my board in H-FLASHER, I receive "Error 5 -
Unknown error", and Flash is Error, and Target is ARM7TDMI-S Litle-Endian.

Thanks for help me.
hi,

please note that H-jatag does not support *.AXF format you have to give
either hex file or binary format to download by the help of H-flasher.
On 19 Mar 2007 09:10:13 -0700, Fernando Barboza wrote:
> -> i like to know whether your h-jtag display the device id ?
> if Yes then please verify following things...
>
> Yes, The H-Jtag display "ARM7TDMI-S" "0x4F1F0F0F".
>
> -> Verify that MAM is disabled, because JTAG is not aware of MAM which
> cause strange problems.
>
> It was set, but with disable, happened problem also.
>
> -> I am also using h-jtag with 2103 & 2104 on keil & it's working
> propery
>
> -> please send more detailed info...
>
> I have receive in Command Window, when I start debug mode.
>
> RDI-Error 5: RDIError_DataAbort
>
> Load
> "C:\\Keil\\ARM\\RV30\\Boards\\Keil\\MCB2100\\Blinky\\Flash\\Blinky.AXF"
>
> RDI-Error 5: RDIError_DataAbort
>
> RDI-Error 5: RDIError_DataAbort
>
> RDI-Error 5: RDIError_DataAbort
>
> RDI-Error 5: RDIError_DataAbort
>
> *** RDI: System-Reset is not supported !
>
> BS \Blinky\61
>
> BS \Blinky\36
>
> I have receive in Command Window, when I try load code.
>
> *** RDI: System-Reset is not supported !
>
> RDI-Error 5: RDIError_DataAbort
>
> RDI-Error 5: RDIError_DataAbort
>
> RDI-Error 5: RDIError_DataAbort
>
> RDI-Error 5: RDIError_DataAbort
>
> *** RDI: System-Reset is not supported !
>
> Now, when I Check my board in H-FLASHER, I receive "Error 5 -
> Unknown error", and Flash is Error, and Target is ARM7TDMI-S Litle-Endian.
>
> Thanks for help me.
>
>
>

--
sandip chudasama
CESES
hi,
Can I to configure H-JTAG or Keil properly?
I to set hex file in Keil, but it try load .axf.
See.

Build target 'MCB2100 Flash'
assembling Startup.s...
compiling Retarget.c...
compiling Serial.c...
compiling Blinky.c...
linking...
FromELF: creating hex file...
".\Flash\Blinky.axf" - 0 Error(s), 0 Warning(s).
Load "C:\\Keil\\ARM\\RV30\\Boards\\Keil\\MCB2100\\Blinky\\Flash\\Blinky.AXF"
*** RDI: System-Reset is not supported !
RDI-Error 5: RDIError_DataAbort
RDI-Error 5: RDIError_DataAbort
RDI-Error 5: RDIError_DataAbort
RDI-Error 5: RDIError_DataAbort
*** RDI: System-Reset is not supported !

In IAR compile, the H-JTAG is good!!
>
>please note that H-jatag does not support *.AXF format you have to give
>either hex file or binary format to download by the help of H-flasher.
>On 19 Mar 2007 09:10:13 -0700, Fernando Barboza wrote:
>> -> i like to know whether your h-jtag display the device id ?
>> if Yes then please verify following things...
>>
>> Yes, The H-Jtag display "ARM7TDMI-S" "0x4F1F0F0F".
>>
>> -> Verify that MAM is disabled, because JTAG is not aware of MAM which
>> cause strange problems.
>>
>> It was set, but with disable, happened problem also.
>>
>> -> I am also using h-jtag with 2103 & 2104 on keil & it's working
>> propery
>>
>> -> please send more detailed info...
>>
>> I have receive in Command Window, when I start debug mode.
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> Load
>> "C:\\Keil\\ARM\\RV30\\Boards\\Keil\\MCB2100\\Blinky\\Flash\\Blinky.AXF"
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> *** RDI: System-Reset is not supported !
>>
>> BS \Blinky\61
>>
>> BS \Blinky\36
>>
>> I have receive in Command Window, when I try load code.
>>
>> *** RDI: System-Reset is not supported !
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> RDI-Error 5: RDIError_DataAbort
>>
>> *** RDI: System-Reset is not supported !
>>
>> Now, when I Check my board in H-FLASHER, I receive "Error 5 -
>> Unknown error", and Flash is Error, and Target is ARM7TDMI-S Litle-Endian.
>>
>> Thanks for help me.
>>
>>
>>--
>sandip chudasama
>CESES
>
>