EmbeddedRelated.com

NEED PROGRAMMING CIRCUIT FOR TMS320F28335

Started by sbhu...@rmsindia.com in TI C200015 years ago 1 reply

Hi all... I am development a general board for TMS320F28335 DSC controller according to my requirement and I got all detail like the reset...

Hi all... I am development a general board for TMS320F28335 DSC controller according to my requirement and I got all detail like the reset circuitry, Flash memory connection etc. But can anyone provide me the programming circuit for it using USB or SCI(UART). Thanks... OMAP35x EVM jump-starts low-power apps The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to star...


FFT calculation F2812

Started by ksvadim in TI C200015 years ago 1 reply

I'm trying to calculate FFT with C28x Fast Fourier Transforms Library (sprc081). The 1-st lamers qestion is why TI use narrow dynamic range -...

I'm trying to calculate FFT with C28x Fast Fourier Transforms Library (sprc081). The 1-st lamers qestion is why TI use narrow dynamic range - Q31 for calculating FFT (range: -1..1), how to work with it if math library doesn't suport it? Another problem is to get right result of fft calculating. At thirst I've tested fft with CFFT32_brev2 bit reversal utility and it works incorrect. CFFT3...


Execution Time calculation using CCS for TMS320F2812

Started by ashu...@yahoo.com in TI C200015 years ago 1 reply

Hello, I am using TMS320F2812 processor along with Code Composer Studio and XDS510USB Emulator. I have got my code running in flash so I have...

Hello, I am using TMS320F2812 processor along with Code Composer Studio and XDS510USB Emulator. I have got my code running in flash so I have got a restriction of setting of maximum of 2 hardware breakpoints in my code. In my code an application/process is hooked to timer2 interrupt which is set for getting called every XYZ milliseconds and my objective is to confirm that the application is ...


ILLEGAL_ISR w/ F28335

Started by Joseph Boike in TI C200016 years ago

Hi, I'm fairly new to DSPs and TI's development tools. I've inherited a project that I'm having a problem with an ILLEGAL_ISR. I'm using CCS...

Hi, I'm fairly new to DSPs and TI's development tools. I've inherited a project that I'm having a problem with an ILLEGAL_ISR. I'm using CCS 3.3 (sp 10)?w/ DSP/BIOS 5_32_04 and code gen tools 5.0.2. The project I inherited runs on a 'F2812 (compiled w/ older tools and CCS). My job is to triple the calculations and get it?to run on new h/w based on the F28335. I have a h/w interrupt that read...


Linker cmd for IQmath in F2812

Started by naay...@gmail.com in TI C200016 years ago 1 reply

Hi all, I want to confirm whether the following linker file is correct for handling IQmath in RAM.Because all my computation values look very...

Hi all, I want to confirm whether the following linker file is correct for handling IQmath in RAM.Because all my computation values look very starnge to me.Can any one of you reply me? Its urgent. If it is wrong then please tell me the correction. Many thanks MEMORY { PAGE 0 : /* For this example, H0 is split between PAGE 0 and PAGE 1 */ /* BEGIN is used for the "boot to HO" bootlo...


Hex-conversion Utility

Started by hema...@gmail.com in TI C200016 years ago 4 replies

Hi friends, I am working with F2812 processor and I want to generate .hex file by hex-conversion utility for flash programming. I...

Hi friends, I am working with F2812 processor and I want to generate .hex file by hex-conversion utility for flash programming. I generated .hex successfully by using command line option. But I want to generate .hex file by using "command file" option i.e for example "hex2000 hexutil.cmd". I followed the steps given in the datasheet Assembly Language Tools for C28x processo...


Problem in ADC of F2812

Started by naay...@gmail.com in TI C200016 years ago

Hi all, I fed 2V and 1V DC signals to ADCIN0 and ADCIN1 respectively and ran my program in F2812 DSP, it didn't work as i have expected. The...

Hi all, I fed 2V and 1V DC signals to ADCIN0 and ADCIN1 respectively and ran my program in F2812 DSP, it didn't work as i have expected. The thing is I observed ADCRESULT0 as 0XFFF0 and ADCRESULT1 as 0xFFF0 in watch window.I have given ADC VREFLO to gnd and the two ADC inputs gnd to the analog ground. Moreover, I have also observed the equivalent voltage after the conversion of digital input by...


same problem in flash programing tms320F28335

Started by zhou...@sina.com in TI C200016 years ago

i met the same problem in flash programing tms320F28335 using \"TMS320F28335 Flash API V1.01\" in CCS 3.354.1 with example along with the api...

i met the same problem in flash programing tms320F28335 using \"TMS320F28335 Flash API V1.01\" in CCS 3.354.1 with example along with the api release. following are codes slice from the example file: \" .............. /*------------------------------------------------------------------ Check the version of the API Flash_APIVersion() returns the version in floating point. Fla...


Maximum support Baudrate of SCI module in F2812

Started by msr_...@yahoo.co.in in TI C200016 years ago 4 replies

Hi All,, I am running my application at 128Mhz system clock out rate on Flash. Is it SCI module support for 5 Mbps baudrate for communicating...

Hi All,, I am running my application at 128Mhz system clock out rate on Flash. Is it SCI module support for 5 Mbps baudrate for communicating another SCI module in F2812.? One more thing is can i have the maximum baudrate of SCI module supports, Thanks in advance Regarsd, Srinu!!! OMAP35x EVM jump-starts low-power apps The modular and extensible OMAP35x Evaluation Module (EVM...


defining constants in IQmath of F2812

Started by naay...@gmail.com in TI C200016 years ago 1 reply

Hi, I have defined few constants like #define conversion 0.534 #define x 25 #define format 666.66667 If i run my program and see the...

Hi, I have defined few constants like #define conversion 0.534 #define x 25 #define format 666.66667 If i run my program and see the values of the variables it was wrong, hence it gave _IQ(conversion) in watch window to view the value, it shows that 'identifier not found : conversion' in the value column of watch window. Why it is? Then how can i ensure that, it has taken defined valu...


Ask a Question to the EmbeddedRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright