Hi all:
I have a board with LPC2103 from ETT
(http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
stoped working, I was testing some hardware with stepper motors and
the uC stopped responding, the code disapeared from the uC and I cant
even reprogram using Philips Flash Utility, talked with a friend and
he told me that maybe the ARM is not burned and maybe the bootloader
erased, my questing is how can I re-program or at least try to...my
board has Jtag probably will be able to re-program by there but I dont
have any programmer or schematic to make one (only have teh RS232
cable), if anyone can help me i'll really apreciate.
Best Regards
Nim
Burned LPC2103!!!
Started by ●June 18, 2008
Reply by ●June 18, 20082008-06-18
----- Original Message -----
From: "nimster6969"
To:
Sent: Wednesday, June 18, 2008 8:36 PM
Subject: [lpc2000] Burned LPC2103!!!
> Hi all:
>
> I have a board with LPC2103 from ETT
> (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> stoped working, I was testing some hardware with stepper motors and
> the uC stopped responding, the code disapeared from the uC and I cant
> even reprogram using Philips Flash Utility, talked with a friend and
> he told me that maybe the ARM is not burned and maybe the bootloader
> erased, my questing is how can I re-program or at least try to...my
> board has Jtag probably will be able to re-program by there but I dont
> have any programmer or schematic to make one (only have teh RS232
> cable), if anyone can help me i'll really apreciate.
I have a simple JTAG design (jtag.zip) in the Files section.
Check all the connections, you might have a bad solder joint. However, you
might need to replace the LPC2103.
Leon
From: "nimster6969"
To:
Sent: Wednesday, June 18, 2008 8:36 PM
Subject: [lpc2000] Burned LPC2103!!!
> Hi all:
>
> I have a board with LPC2103 from ETT
> (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> stoped working, I was testing some hardware with stepper motors and
> the uC stopped responding, the code disapeared from the uC and I cant
> even reprogram using Philips Flash Utility, talked with a friend and
> he told me that maybe the ARM is not burned and maybe the bootloader
> erased, my questing is how can I re-program or at least try to...my
> board has Jtag probably will be able to re-program by there but I dont
> have any programmer or schematic to make one (only have teh RS232
> cable), if anyone can help me i'll really apreciate.
I have a simple JTAG design (jtag.zip) in the Files section.
Check all the connections, you might have a bad solder joint. However, you
might need to replace the LPC2103.
Leon
Reply by ●June 19, 20082008-06-19
You can build easy wiggler for test your board. schematic
http://www.hjtag.com/download/WIGGLER2.rar
It work perfect with H-JTAG software :)
--
http://www.micro4you.com -> mini N-Link ARM USB JTAG
http://stores.ebay.com/Micro4you-Store -> Ebay Store
http://astore.amazon.com/micro4you-20 -> Embedded System Books
http://www.friendlyarm.com
On Thu, Jun 19, 2008 at 2:51 AM, Leon wrote:
> ----- Original Message -----
> From: "nimster6969" >
> To: >
> Sent: Wednesday, June 18, 2008 8:36 PM
> Subject: [lpc2000] Burned LPC2103!!!
>
>
> > Hi all:
> >
> > I have a board with LPC2103 from ETT
> > (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> > stoped working, I was testing some hardware with stepper motors and
> > the uC stopped responding, the code disapeared from the uC and I cant
> > even reprogram using Philips Flash Utility, talked with a friend and
> > he told me that maybe the ARM is not burned and maybe the bootloader
> > erased, my questing is how can I re-program or at least try to...my
> > board has Jtag probably will be able to re-program by there but I dont
> > have any programmer or schematic to make one (only have teh RS232
> > cable), if anyone can help me i'll really apreciate.
>
> I have a simple JTAG design (jtag.zip) in the Files section.
>
> Check all the connections, you might have a bad solder joint. However, you
> might need to replace the LPC2103.
>
> Leon
>
>
>
--
http://www.micro4you.com -> mini N-Link ARM USB JTAG
http://stores.ebay.com/Micro4you-Store -> Ebay Store
http://astore.amazon.com/micro4you-20 -> Embedded System Books
http://www.friendlyarm.com
It work perfect with H-JTAG software :)
--
http://www.micro4you.com -> mini N-Link ARM USB JTAG
http://stores.ebay.com/Micro4you-Store -> Ebay Store
http://astore.amazon.com/micro4you-20 -> Embedded System Books
http://www.friendlyarm.com
On Thu, Jun 19, 2008 at 2:51 AM, Leon wrote:
> ----- Original Message -----
> From: "nimster6969" >
> To: >
> Sent: Wednesday, June 18, 2008 8:36 PM
> Subject: [lpc2000] Burned LPC2103!!!
>
>
> > Hi all:
> >
> > I have a board with LPC2103 from ETT
> > (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> > stoped working, I was testing some hardware with stepper motors and
> > the uC stopped responding, the code disapeared from the uC and I cant
> > even reprogram using Philips Flash Utility, talked with a friend and
> > he told me that maybe the ARM is not burned and maybe the bootloader
> > erased, my questing is how can I re-program or at least try to...my
> > board has Jtag probably will be able to re-program by there but I dont
> > have any programmer or schematic to make one (only have teh RS232
> > cable), if anyone can help me i'll really apreciate.
>
> I have a simple JTAG design (jtag.zip) in the Files section.
>
> Check all the connections, you might have a bad solder joint. However, you
> might need to replace the LPC2103.
>
> Leon
>
>
>
--
http://www.micro4you.com -> mini N-Link ARM USB JTAG
http://stores.ebay.com/Micro4you-Store -> Ebay Store
http://astore.amazon.com/micro4you-20 -> Embedded System Books
http://www.friendlyarm.com
Reply by ●June 19, 20082008-06-19
Well the big problem is that i dont even know if I can program the uC
with J-Tag, ive tried to use Philips Flash Utility and some
bootloaders that came on the CD but cant even get connection with the
PC :(.
--- In l..., "somboon sopee" wrote:
>
> You can build easy wiggler for test your board. schematic > http://www.hjtag.com/download/WIGGLER2.rar
> It work perfect with H-JTAG software :)
>
> --
> http://www.micro4you.com -> mini N-Link ARM USB JTAG
> http://stores.ebay.com/Micro4you-Store -> Ebay Store
> http://astore.amazon.com/micro4you-20 -> Embedded System Books
> http://www.friendlyarm.com
>
> On Thu, Jun 19, 2008 at 2:51 AM, Leon wrote:
>
> > ----- Original Message -----
> > From: "nimster6969" >
> > To: >
> > Sent: Wednesday, June 18, 2008 8:36 PM
> > Subject: [lpc2000] Burned LPC2103!!!
> > >
> > > Hi all:
> > >
> > > I have a board with LPC2103 from ETT
> > > (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> > > stoped working, I was testing some hardware with stepper motors and
> > > the uC stopped responding, the code disapeared from the uC and I
cant
> > > even reprogram using Philips Flash Utility, talked with a friend and
> > > he told me that maybe the ARM is not burned and maybe the bootloader
> > > erased, my questing is how can I re-program or at least try to...my
> > > board has Jtag probably will be able to re-program by there but
I dont
> > > have any programmer or schematic to make one (only have teh RS232
> > > cable), if anyone can help me i'll really apreciate.
> >
> > I have a simple JTAG design (jtag.zip) in the Files section.
> >
> > Check all the connections, you might have a bad solder joint.
However, you
> > might need to replace the LPC2103.
> >
> > Leon
> >
> >
> > --
> http://www.micro4you.com -> mini N-Link ARM USB JTAG
> http://stores.ebay.com/Micro4you-Store -> Ebay Store
> http://astore.amazon.com/micro4you-20 -> Embedded System Books
> http://www.friendlyarm.com
>
>
with J-Tag, ive tried to use Philips Flash Utility and some
bootloaders that came on the CD but cant even get connection with the
PC :(.
--- In l..., "somboon sopee" wrote:
>
> You can build easy wiggler for test your board. schematic > http://www.hjtag.com/download/WIGGLER2.rar
> It work perfect with H-JTAG software :)
>
> --
> http://www.micro4you.com -> mini N-Link ARM USB JTAG
> http://stores.ebay.com/Micro4you-Store -> Ebay Store
> http://astore.amazon.com/micro4you-20 -> Embedded System Books
> http://www.friendlyarm.com
>
> On Thu, Jun 19, 2008 at 2:51 AM, Leon wrote:
>
> > ----- Original Message -----
> > From: "nimster6969" >
> > To: >
> > Sent: Wednesday, June 18, 2008 8:36 PM
> > Subject: [lpc2000] Burned LPC2103!!!
> > >
> > > Hi all:
> > >
> > > I have a board with LPC2103 from ETT
> > > (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> > > stoped working, I was testing some hardware with stepper motors and
> > > the uC stopped responding, the code disapeared from the uC and I
cant
> > > even reprogram using Philips Flash Utility, talked with a friend and
> > > he told me that maybe the ARM is not burned and maybe the bootloader
> > > erased, my questing is how can I re-program or at least try to...my
> > > board has Jtag probably will be able to re-program by there but
I dont
> > > have any programmer or schematic to make one (only have teh RS232
> > > cable), if anyone can help me i'll really apreciate.
> >
> > I have a simple JTAG design (jtag.zip) in the Files section.
> >
> > Check all the connections, you might have a bad solder joint.
However, you
> > might need to replace the LPC2103.
> >
> > Leon
> >
> >
> > --
> http://www.micro4you.com -> mini N-Link ARM USB JTAG
> http://stores.ebay.com/Micro4you-Store -> Ebay Store
> http://astore.amazon.com/micro4you-20 -> Embedded System Books
> http://www.friendlyarm.com
>
>
Reply by ●June 19, 20082008-06-19
----- Original Message -----
From: "nimster6969"
To:
Sent: Thursday, June 19, 2008 11:11 AM
Subject: [lpc2000] Re: Burned LPC2103!!!
> Well the big problem is that i dont even know if I can program the uC
> with J-Tag, ive tried to use Philips Flash Utility and some
> bootloaders that came on the CD but cant even get connection with the
> PC :(.
Have you checked the solder joints as I suggested?
Leon
From: "nimster6969"
To:
Sent: Thursday, June 19, 2008 11:11 AM
Subject: [lpc2000] Re: Burned LPC2103!!!
> Well the big problem is that i dont even know if I can program the uC
> with J-Tag, ive tried to use Philips Flash Utility and some
> bootloaders that came on the CD but cant even get connection with the
> PC :(.
Have you checked the solder joints as I suggested?
Leon
Reply by ●June 19, 20082008-06-19
--- In l..., "nimster6969" wrote:
>
> Hi all:
>
> I have a board with LPC2103 from ETT
> (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> stoped working, I was testing some hardware with stepper motors and
> the uC stopped responding, the code disappeared from the uC and I cant
> even reprogram using Philips Flash Utility, talked with a friend and
> he told me that maybe the ARM is not burned and maybe the bootloader
> erased, my questing is how can I re-program or at least try to...my
> board has Jtag probably will be able to re-program by there but I dont
> have any programmer or schematic to make one (only have teh RS232
> cable), if anyone can help me i'll really appreciate.
>
> Best Regards
> Nim
>
Nim,
you can not erase the bootloader of the LPC2103 because it is not in a
Flash memory, it is a real ROM memory. So, you may exclude that option
from your debugging efforts. Most LPCs have the bootloader in a part
of the Flash but this one, the LPC2101/2/3 have it in a MaskROM.
Bob
>
> Hi all:
>
> I have a board with LPC2103 from ETT
> (http://www.futurlec.com/ARM2103_Controller.shtml) and sudenly it
> stoped working, I was testing some hardware with stepper motors and
> the uC stopped responding, the code disappeared from the uC and I cant
> even reprogram using Philips Flash Utility, talked with a friend and
> he told me that maybe the ARM is not burned and maybe the bootloader
> erased, my questing is how can I re-program or at least try to...my
> board has Jtag probably will be able to re-program by there but I dont
> have any programmer or schematic to make one (only have teh RS232
> cable), if anyone can help me i'll really appreciate.
>
> Best Regards
> Nim
>
Nim,
you can not erase the bootloader of the LPC2103 because it is not in a
Flash memory, it is a real ROM memory. So, you may exclude that option
from your debugging efforts. Most LPCs have the bootloader in a part
of the Flash but this one, the LPC2101/2/3 have it in a MaskROM.
Bob
