Dear Srs,
We are experimenting the ISP downloading using the LPC2142 using the
Philips Flash Utility 2.2.1 on our board.
When we hit the "Read Device" bottom of the utility we got the
following message "TYPE NOT SUPPORTED" even receiving the ID number
and
the Version Loader 2.1.of the micro controller.
It seens to me that it is not a hardware problem because the
TX,RX,reset and P0.14 are identical of the Keil Demo board.
(the demo board uses the LPC2148)
Does anybody has a idea of what's going on?
Regards,
Jan
LPC2000 Flash Utility
Started by ●September 16, 2005
Reply by ●September 16, 20052005-09-16
The latest version of the software can be found at
www.philips.com/microcontrollers
The new version is 2.2.2. This version supports 214x.
Amit
--- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
> Dear Srs,
>
> We are experimenting the ISP downloading using the LPC2142 using
the
> Philips Flash Utility 2.2.1 on our board.
> When we hit the "Read Device" bottom of the utility we got the
> following message "TYPE NOT SUPPORTED" even receiving the ID number
and
> the Version Loader 2.1.of the micro controller.
> It seens to me that it is not a hardware problem because the
> TX,RX,reset and P0.14 are identical of the Keil Demo board.
> (the demo board uses the LPC2148)
> Does anybody has a idea of what's going on?
>
> Regards,
> Jan
www.philips.com/microcontrollers
The new version is 2.2.2. This version supports 214x.
Amit
--- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
> Dear Srs,
>
> We are experimenting the ISP downloading using the LPC2142 using
the
> Philips Flash Utility 2.2.1 on our board.
> When we hit the "Read Device" bottom of the utility we got the
> following message "TYPE NOT SUPPORTED" even receiving the ID number
and
> the Version Loader 2.1.of the micro controller.
> It seens to me that it is not a hardware problem because the
> TX,RX,reset and P0.14 are identical of the Keil Demo board.
> (the demo board uses the LPC2148)
> Does anybody has a idea of what's going on?
>
> Regards,
> Jan
Reply by ●September 18, 20052005-09-18
amit,
can you help me with how can i enter isp mode for lpc2106
i am using lpc flash utility v2.2.1
when i press "read device id" it gives the message "cannot communicate with the demo board"
please reply soon
regards
vicky
Amit <emailakb@emai...> wrote:
The latest version of the software can be found at
www.philips.com/microcontrollers
The new version is 2.2.2. This version supports 214x.
Amit
--- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
> Dear Srs,
>
> We are experimenting the ISP downloading using the LPC2142 using
the
> Philips Flash Utility 2.2.1 on our board.
> When we hit the "Read Device" bottom of the utility we got the
> following message "TYPE NOT SUPPORTED" even receiving the ID number
and
> the Version Loader 2.1.of the micro controller.
> It seens to me that it is not a hardware problem because the
> TX,RX,reset and P0.14 are identical of the Keil Demo board.
> (the demo board uses the LPC2148)
> Does anybody has a idea of what's going on?
>
> Regards,
> Jan
---------------------------------
YAHOO! GROUPS LINKS ---------------------------------
---------------------------------
Yahoo! India Matrimony: Find your partner now.
can you help me with how can i enter isp mode for lpc2106
i am using lpc flash utility v2.2.1
when i press "read device id" it gives the message "cannot communicate with the demo board"
please reply soon
regards
vicky
Amit <emailakb@emai...> wrote:
The latest version of the software can be found at
www.philips.com/microcontrollers
The new version is 2.2.2. This version supports 214x.
Amit
--- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
> Dear Srs,
>
> We are experimenting the ISP downloading using the LPC2142 using
the
> Philips Flash Utility 2.2.1 on our board.
> When we hit the "Read Device" bottom of the utility we got the
> following message "TYPE NOT SUPPORTED" even receiving the ID number
and
> the Version Loader 2.1.of the micro controller.
> It seens to me that it is not a hardware problem because the
> TX,RX,reset and P0.14 are identical of the Keil Demo board.
> (the demo board uses the LPC2148)
> Does anybody has a idea of what's going on?
>
> Regards,
> Jan
---------------------------------
YAHOO! GROUPS LINKS ---------------------------------
---------------------------------
Yahoo! India Matrimony: Find your partner now.
Reply by ●September 18, 20052005-09-18
Hello,
use a speed of 9600 for beginning and put the jumper to ISP (at least if it
is the same as the LPC2138 board).
If this is working you can increase speed, up to i think, 38400 (this is
because a 12 MHz oscillator is used on the board).
Regards,
Martin
----- Original Message -----
From: "vicky gosar" <vickygosar@vick...>
To: <lpc2000@lpc2...>
Sent: Sunday, September 18, 2005 2:17 PM
Subject: Re: [lpc2000] Re: LPC2000 Flash Utility > amit,
>
> can you help me with how can i enter isp mode for lpc2106
>
> i am using lpc flash utility v2.2.1
>
> when i press "read device id" it gives the message "cannot communicate
> with the demo board"
>
> please reply soon
>
> regards
> vicky
>
> Amit <emailakb@emai...> wrote:
> The latest version of the software can be found at
> www.philips.com/microcontrollers
>
> The new version is 2.2.2. This version supports 214x.
>
> Amit
>
> --- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
>> Dear Srs,
>>
>> We are experimenting the ISP downloading using the LPC2142 using
> the
>> Philips Flash Utility 2.2.1 on our board.
>> When we hit the "Read Device" bottom of the utility we got the
>> following message "TYPE NOT SUPPORTED" even receiving the ID number
> and
>> the Version Loader 2.1.of the micro controller.
>> It seens to me that it is not a hardware problem because the
>> TX,RX,reset and P0.14 are identical of the Keil Demo board.
>> (the demo board uses the LPC2148)
>> Does anybody has a idea of what's going on?
>>
>> Regards,
>> Jan >
>
> ---------------------------------
> YAHOO! GROUPS LINKS > --------------------------------- >
>
> ---------------------------------
> Yahoo! India Matrimony: Find your partner now. >
>
> Yahoo! Groups Links >
>
use a speed of 9600 for beginning and put the jumper to ISP (at least if it
is the same as the LPC2138 board).
If this is working you can increase speed, up to i think, 38400 (this is
because a 12 MHz oscillator is used on the board).
Regards,
Martin
----- Original Message -----
From: "vicky gosar" <vickygosar@vick...>
To: <lpc2000@lpc2...>
Sent: Sunday, September 18, 2005 2:17 PM
Subject: Re: [lpc2000] Re: LPC2000 Flash Utility > amit,
>
> can you help me with how can i enter isp mode for lpc2106
>
> i am using lpc flash utility v2.2.1
>
> when i press "read device id" it gives the message "cannot communicate
> with the demo board"
>
> please reply soon
>
> regards
> vicky
>
> Amit <emailakb@emai...> wrote:
> The latest version of the software can be found at
> www.philips.com/microcontrollers
>
> The new version is 2.2.2. This version supports 214x.
>
> Amit
>
> --- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
>> Dear Srs,
>>
>> We are experimenting the ISP downloading using the LPC2142 using
> the
>> Philips Flash Utility 2.2.1 on our board.
>> When we hit the "Read Device" bottom of the utility we got the
>> following message "TYPE NOT SUPPORTED" even receiving the ID number
> and
>> the Version Loader 2.1.of the micro controller.
>> It seens to me that it is not a hardware problem because the
>> TX,RX,reset and P0.14 are identical of the Keil Demo board.
>> (the demo board uses the LPC2148)
>> Does anybody has a idea of what's going on?
>>
>> Regards,
>> Jan >
>
> ---------------------------------
> YAHOO! GROUPS LINKS > --------------------------------- >
>
> ---------------------------------
> Yahoo! India Matrimony: Find your partner now. >
>
> Yahoo! Groups Links >
>
Reply by ●September 19, 20052005-09-19
Amit,
Using the Flash utility 2.2.2 version it works now.
Thank a lot for your information. Regards,
Jan
_____
De: Amit [mailto:emailakb@emai...]
Enviada em: sexta-feira, 16 de setembro de 2005 18:48
Para: lpc2000@lpc2...
Assunto: [lpc2000] Re: LPC2000 Flash Utility
The latest version of the software can be found at
www.philips.com/microcontrollers
The new version is 2.2.2. This version supports 214x.
Amit
--- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
> Dear Srs,
>
> We are experimenting the ISP downloading using the LPC2142 using
the
> Philips Flash Utility 2.2.1 on our board.
> When we hit the "Read Device" bottom of the utility we got the
> following message "TYPE NOT SUPPORTED" even receiving the ID number
and
> the Version Loader 2.1.of the micro controller.
> It seens to me that it is not a hardware problem because the
> TX,RX,reset and P0.14 are identical of the Keil Demo board.
> (the demo board uses the LPC2148)
> Does anybody has a idea of what's going on?
>
> Regards,
> Jan
_____
> .
_____
Using the Flash utility 2.2.2 version it works now.
Thank a lot for your information. Regards,
Jan
_____
De: Amit [mailto:emailakb@emai...]
Enviada em: sexta-feira, 16 de setembro de 2005 18:48
Para: lpc2000@lpc2...
Assunto: [lpc2000] Re: LPC2000 Flash Utility
The latest version of the software can be found at
www.philips.com/microcontrollers
The new version is 2.2.2. This version supports 214x.
Amit
--- In lpc2000@lpc2..., "janduchateau" <jan@p...> wrote:
> Dear Srs,
>
> We are experimenting the ISP downloading using the LPC2142 using
the
> Philips Flash Utility 2.2.1 on our board.
> When we hit the "Read Device" bottom of the utility we got the
> following message "TYPE NOT SUPPORTED" even receiving the ID number
and
> the Version Loader 2.1.of the micro controller.
> It seens to me that it is not a hardware problem because the
> TX,RX,reset and P0.14 are identical of the Keil Demo board.
> (the demo board uses the LPC2148)
> Does anybody has a idea of what's going on?
>
> Regards,
> Jan
_____
> .
_____