Hi! i've got crossworks 1.3 and MSP-FET430UIF from TI. When i connect
crossworks to FET (menu:target->connect msp430uif) i got weird
problem. error shows: external voltage is detected, but if i turn off
power supply of my msp430, then nothing happen:( but if i click
target->connect msp430uif usb and after 1 second turn on power
supply, all is ok. More: i have no problem with Lite FET-Pro430
Elprotronic programmer! it starts every time! what i'm doing wrong
with crossworks? (jtag pins are connected ok, i've checked this
thousands times:) see: elptronic is working more than good! :))
crossworks and MSP-FET430UIF
Started by ●September 20, 2006
Reply by ●September 20, 20062006-09-20
You need to set the Vcc in the target interface of the UIF to 0 so that
the UIF is configured not to power the target.
--
Paul Curtis, Rowley Associates Ltd http://www.rowley.co.uk
CrossWorks for ARM, MSP430, AVR, MAXQ, and now Cortex-M3 processors
> -----Original Message-----
> From: les_kamil [mailto:k...@tlen.pl]
> Sent: 20 September 2006 05:55
> To: m...
> Subject: [msp430] crossworks and MSP-FET430UIF
>
> Hi! i've got crossworks 1.3 and MSP-FET430UIF from TI. When i
> connect crossworks to FET (menu:target->connect msp430uif) i
> got weird problem. error shows: external voltage is detected,
> but if i turn off power supply of my msp430, then nothing
> happen:( but if i click
> target->connect msp430uif usb and after 1 second turn on power
> supply, all is ok. More: i have no problem with Lite
> FET-Pro430 Elprotronic programmer! it starts every time! what
> i'm doing wrong with crossworks? (jtag pins are connected ok,
> i've checked this thousands times:) see: elptronic is working
> more than good! :))
>
>
>
the UIF is configured not to power the target.
--
Paul Curtis, Rowley Associates Ltd http://www.rowley.co.uk
CrossWorks for ARM, MSP430, AVR, MAXQ, and now Cortex-M3 processors
> -----Original Message-----
> From: les_kamil [mailto:k...@tlen.pl]
> Sent: 20 September 2006 05:55
> To: m...
> Subject: [msp430] crossworks and MSP-FET430UIF
>
> Hi! i've got crossworks 1.3 and MSP-FET430UIF from TI. When i
> connect crossworks to FET (menu:target->connect msp430uif) i
> got weird problem. error shows: external voltage is detected,
> but if i turn off power supply of my msp430, then nothing
> happen:( but if i click
> target->connect msp430uif usb and after 1 second turn on power
> supply, all is ok. More: i have no problem with Lite
> FET-Pro430 Elprotronic programmer! it starts every time! what
> i'm doing wrong with crossworks? (jtag pins are connected ok,
> i've checked this thousands times:) see: elptronic is working
> more than good! :))
>
>
>
Reply by ●September 20, 20062006-09-20
--- In m..., "Paul Curtis" wrote:
>
> You need to set the Vcc in the target interface of the UIF to 0 so
that
> the UIF is configured not to power the target.
yeah:) in UIF manual the arrows are in wrong directions! in text is
good but in circuit is wrong:) i had target vcc connected to pin4 of
jtag
>
> You need to set the Vcc in the target interface of the UIF to 0 so
that
> the UIF is configured not to power the target.
yeah:) in UIF manual the arrows are in wrong directions! in text is
good but in circuit is wrong:) i had target vcc connected to pin4 of
jtag
