Hi ! My web-page with jtag tools for SAM7S is upgraded. It contains a flash programmer, a gdb server and directions for making a cheap USB...

Hi ! My web-page with jtag tools for SAM7S is upgraded. It contains a flash programmer, a gdb server and directions for making a cheap USB jtag adapter. Check http://kjell.e.andersen.googlepages.com/ -kjell eirik

Hi guys, I've build my own SAM9260 board and now trying to get the hardware working. My problem at the moment is the JTAG interface. The...

Hi guys, I've build my own SAM9260 board and now trying to get the hardware working. My problem at the moment is the JTAG interface. The PEEDI from Ronetix show me a BYPASS error, but ignores it and so it is possibe to access the registers and configure the 9260 via JTAG. My FT2232 based debugger with OpenOCD fails due to a JTAG error. I think this is because of the BYPASS error. ...

Hello friends, i recently get my AT91SAM7S-EK; for JTAG connection i got an ARM wiggler that goes from JTAG port to DB25. Since my lap has no DB25...

Hello friends, i recently get my AT91SAM7S-EK; for JTAG connection i got an ARM wiggler that goes from JTAG port to DB25. Since my lap has no DB25 port i have to connect the wiggler to a DB25 - DB9 - USB cable. (which means that i have a device that converts a DB25 to DB9 and that DB9 output is then connected to a DB9-to-USB cable) Now, i'm working with openOCD but i don't exactly now what i ha...

I'm a complete noob to the ARM controllers. I picked up an AT91ARM7S 256 and I'm making up a prototype board of my own. I'd like to make up a...

I'm a complete noob to the ARM controllers. I picked up an AT91ARM7S 256 and I'm making up a prototype board of my own. I'd like to make up a DIY JTAG as well. Will this Xilinx schematic work with WinARM or GNUARM? I've seen other schematics that are based on the 74HC244, like the one in the files section of the Yahoo group, but I've already thrown this into Eagle, and I already have ...

Hi Fellas, I am working on a project and no JTAG debugger is available for me. The current approach I'm using is simply printing variables to...

Hi Fellas, I am working on a project and no JTAG debugger is available for me. The current approach I'm using is simply printing variables to DBGU port and frustrating trial/error process. There are three wires connecting to my device now ( beside supply voltage) that are capable of data transfer : DBGU (Currently Debugging), USB (ISP and Data) and Ethernet (Data) interfaces which are all fu...

Hi i recently bought an ARM7 kit from olimex SAM7EX256.i plan to put together my own jtag wiggler. but there seem to be so many schematics on...

Hi i recently bought an ARM7 kit from olimex SAM7EX256.i plan to put together my own jtag wiggler. but there seem to be so many schematics on the net. Does anyone have the schematic of the wiggler which is known to work with the olimex board or any olimex board with SAM7?

Hello Group I'm using IAR embedded workbench and SAM-ICE with the AT91SAM7L-STK and I keep getting the error "Could not find supported CPU...

Hello Group I'm using IAR embedded workbench and SAM-ICE with the AT91SAM7L-STK and I keep getting the error "Could not find supported CPU core on JTAG chain" when I try to download and debug. jlink.exe shows the same thing. Does the SAM-ICE not support the new AT91SAM7L128??? Thanks! trwinok ------------------------------------

Hai All, Iam having a parallel port JTAG wiggler from olimex.I want to use it to debug linux kernel,drivers etc. I have some questions...

Hai All, Iam having a parallel port JTAG wiggler from olimex.I want to use it to debug linux kernel,drivers etc. I have some questions which I want to have clarity: 1)what kind of parallel port cable is neccesary to use the wiggler? 2)Are there any extra connections neccesary? 3)One of the documents available on the net specifies that there needs to be a short between pins 8 and 15 on t...

Hi I am new in the world of ARM, I have been researching the web to find a proper start up tutorial on ARM. For example if I have an ARM...

Hi I am new in the world of ARM, I have been researching the web to find a proper start up tutorial on ARM. For example if I have an ARM board how do I create the startup code and set up the environment to compile C code to a format that I can download via JTAG to the processor. Thanks. Any help would be greatly appreciated. ------------------------------------

Hi all, I'm working on setting up a development environment using Kdevelop and FreeRTOS for the SAM7S64. It's taken a bit of work...

Hi all, I'm working on setting up a development environment using Kdevelop and FreeRTOS for the SAM7S64. It's taken a bit of work because the FreeRTOS port and demo app weren't finished and all of the ISRs had to be rewritten, among other things. I've also got it working (to some extent at least) with a remote J-Link JTAG pod. For troubleshoot

I have a custom board designed with SAM7X256. I have successfully runned some applications on the Board via programming JTAG. However, I cannot...

I have a custom board designed with SAM7X256. I have successfully runned some applications on the Board via programming JTAG. However, I cannot run SAM-BA boot. I have tested USB port of board and it is working. I'm erasing the flash ( via TST pin ). But I cannot emulate sam-ba on PC. I tried both atm6124.inf and atm6124ser.inf. BTW, I can program AT91SAM7X-EK via SAM-BA. Windows sees my boar...

Does anyone have an AT91SAM3U-EK? A simple search for the board on this group did not yield any hits. I am trying to use Atmel's sample code...

Does anyone have an AT91SAM3U-EK? A simple search for the board on this group did not yield any hits. I am trying to use Atmel's sample code along side of Jim Lynch's open source development tutorial with the SAM-ICE JTAG programmer but I am unable to properly set up the debugger. YAGARTO has a sample project for the AT91SAM3U-EK that I am able to debug but I don't understand it well enough ...

Gentlemen: if you are using embedded Linux, with an AT91SAM7x, then could you share your experience: * Which Linux * Which Tools...

Gentlemen: if you are using embedded Linux, with an AT91SAM7x, then could you share your experience: * Which Linux * Which Tools (Compiler, JTAG interface, debugger...) * Which AT91SAM7S and which config (external DRAM? etc...) * What is the good, the bad etc... Thank you. a.g Andre Gompel a...@yahoo.com _______________________________________________________________...

I'm having some trouble programming the AT91SAM9261, and I'm hoping someone out there can point me in the right direction. I'm using the...

I'm having some trouble programming the AT91SAM9261, and I'm hoping someone out there can point me in the right direction. I'm using the latest yagarto tool chain to program the AT91SAM9261. I'm connecting to the chip using the Atmel SAM-ICE JTAG via USB. I have tried to follow the sometimes conflicting setup info in the documents "Using Open Source Tools for AT91SAM7S Cross Development ...

Hi I need help me for start programmer at91sam7x256 please let me know how to program...

Hi I need help me for start programmer at91sam7x256 please let me know how to program at91sam7x256 ____________________________________________________________________________________ 8:00? 8:25? 8:40? Find a flick in no time with the Yahoo! Search movie showtime shortcut. http://tools.search.yahoo.com/shortcuts/#news

Have built 650 units using the AT91SAM7S256AU Rev A chip. Next build used Rev B chip Ocaisoinal problems are encountered with starting the...

Have built 650 units using the AT91SAM7S256AU Rev A chip. Next build used Rev B chip Ocaisoinal problems are encountered with starting the processor from power up. The application is running under Keil RTX. No changes make to code between Rev A and Rev B build. Using the JTAG to investigate shows the processor to be hung initializing the RTX. The main function is called which calls the os_sys...

Dear senior members, I am new bie to ARM7. I have two similar devices having at91sam7s128 controller on it. I have the firmware, code written...

Dear senior members, I am new bie to ARM7. I have two similar devices having at91sam7s128 controller on it. I have the firmware, code written in 4.4 version of IAR. Intially it was progrmming fine. I tried to write my own code and in that process i tried to run the 5.3 version IAR example on the device and it was working also. The 4.4 code was not migrating to 5.3 so i replaced the 5.3 example ...

I am stepping through the "Using Open Source Tools for AT91SAM7S Cross Development" tutorial by James P. Lynch and I am getting hung up when I...

I am stepping through the "Using Open Source Tools for AT91SAM7S Cross Development" tutorial by James P. Lynch and I am getting hung up when I try to program the board. I keep getting the following error: **** Build of configuration MinGW GCC for project demo_at91sam7_blink_flash **** make -k program Flash Programming with OpenOCD... 'c:/Program Files/openocd-2007re204/bin/'openocd-ftd2...

I am new user of AT91SAM7S64, can I use the DEBUG UART to DEBUG programn like JTAG or only use it to download programn to flash through...

I am new user of AT91SAM7S64, can I use the DEBUG UART to DEBUG programn like JTAG or only use it to download programn to flash through SAM-BA?

I am very much interested in an example software showing the workings of even just a "simple" (massive understatement) interrupt. As I can...

I am very much interested in an example software showing the workings of even just a "simple" (massive understatement) interrupt. As I can only access my board via the Samba it must be either running from ram or able to be programmed in flash via Samba (I do not have any jtag connection available). My system consist of : Developement server running : Debian 5.0 arm-elf-gcc (GCC...