Forums More hc11
PT1000 interface
inAnybody ever interfaced with a four wire platinum resistor PT1000? I found a Smartec device that connects directly to the...
Anybody ever interfaced with a four wire platinum resistor PT1000? I found a Smartec device that connects directly to the transducer and and produces a micro-combatible period-modulated output signal without any other electronics. Are there any potential problems with creating in
Re: HC11 IRQ AND XIRQ PIN 40 AND 41
inPlease don't shout, we're all deaf here, anyway. :) Your understanding of IRQ is good. XIRQ is similar to IRQ with some...
Please don't shout, we're all deaf here, anyway. :) Your understanding of IRQ is good. XIRQ is similar to IRQ with some exceptions: 1. Once enabled, XIRQ cannot be disabled (actually it can be, but it shouldn't in theory as it said to be a non-maskable interrupt)
Temperature Sensor
inHi all. I am newbie in 6811. I have a final project to do. And I want to know how to integrate the temperature sensor to the...
Hi all. I am newbie in 6811. I have a final project to do. And I want to know how to integrate the temperature sensor to the M68HC11? But firstly, I need to know the best sensor to use.. tq
Illegal opcode
inHi Everyone, My code locks-up in an infinite loop by getting into the Illegal Opcode interrupt routine. Now the book says the...
Hi Everyone, My code locks-up in an infinite loop by getting into the Illegal Opcode interrupt routine. Now the book says the way to get out of this is by popping/pulling the stack of the return address of the illegal opcode. I know I can do this by using the In-line assembly
Re: replacement for the 68HC811E2??
Dream on Kerry, dream on .... You should have saved this for 4/1/04 . Bob --- Avoid computer viruses, Practice safe...
Dream on Kerry, dream on .... You should have saved this for 4/1/04 . Bob --- Avoid computer viruses, Practice safe hex --- -- Specializing in small, cost effective embedded control systems --
Re: reading the 68HC711 code
Daniel, The direct answer to your question is "yes". However, you probably want a little more information. If your 68hc711...
Daniel, The direct answer to your question is "yes". However, you probably want a little more information. If your 68hc711 is in a board, you may not be able to invoke the various non-user modes. However, if you have the part in your hot little hand and can take it to so
traffic light control system
inhello, i want to control traffic light signals through M68hc11 .the approach is ,when a car come, the signal will turn on...
hello, i want to control traffic light signals through M68hc11 .the approach is ,when a car come, the signal will turn on otherwise turn off.i want to know the code of this program .if any one know let me aware too . thax tanveer haider
M68HC11EVM & Windows XP
inI have a Motorola M68HC11EVM evaluation module that I purchased from Motorola in the early 1990s (- quit laughing! It's a good...
I have a Motorola M68HC11EVM evaluation module that I purchased from Motorola in the early 1990s (- quit laughing! It's a good system!). The DOS-based software that came with the EVM has the following sign-on screen: "User interface to the Motorola M68HC11EVM Requir
EVM
in"When you say that you have an EVM, do you mean the big board that is a little bit bigger than a standard size sheet of paper?" ...
"When you say that you have an EVM, do you mean the big board that is a little bit bigger than a standard size sheet of paper?" Yup, that's the one! Heck of a nice system, especially with the P&E GUI. It was nice to work in multiple Windows that included the EVM,
REALLY NEED HELP TO DO DIVISION in assembly
inHi, I have a 16-bit variable that is needed to be multiplied by 5 (decimal) and then divided by 1000000 (decimal, too)...so it is...
Hi, I have a 16-bit variable that is needed to be multiplied by 5 (decimal) and then divided by 1000000 (decimal, too)...so it is like multiplying by 0.000005 (decimal),,,,,,ANY IDEA HOW TO DO THAT???? I really need help...ASAP thanx all AA
Ask a Question to the EmbeddedRelated community
To significantly increase your chances of receiving answers, please make sure to:
- Use a meaningful title
- Express your question clearly and well
- Do not use this forum to promote your product, service or business
- Write in clear, grammatical, correctly-spelled language
- Do not post content that violates a copyright