USB on Rabbit

Started by river_rat_692000 in Rabbit-Semi14 years ago 2 replies

I've looked through the archives, and it seems that no one has implemented a USB stack for the Rabbit yet. I need USB functionality for...

I've looked through the archives, and it seems that no one has implemented a USB stack for the Rabbit yet. I need USB functionality for mass storage class devices but not the entire USB stack. If anyone has some working code I could look over to get some ideas I would greatly appreciate it. Jeffrey


USB (max3420e) with RCM3720

Started by isaceh in Rabbit-Semi10 years ago

Hello everybody, I'm trying to connect a Rabbit RCM3720 to a PC using USB (in SPI mode). I use a chip max3420e as adapter for the USB. I use...

Hello everybody, I'm trying to connect a Rabbit RCM3720 to a PC using USB (in SPI mode). I use a chip max3420e as adapter for the USB. I use the maxim's software found in http://www.maxim-ic.com/appnotes.cfm/an_pk/3690 and I emmule this application after translating it into dynamic C. The result isn't the expected because the PC can't recognize the USB interfice. Can somebody help me? Th...


Programming over USB

Started by "see...@yahoo.com [rabbit-semi]" in Rabbit-Semi2 years ago 3 replies

Has anyone successfully programmed an R3k module using the clrfu and a USB adapter? The manual says using USB is an option, but I can't get it...

Has anyone successfully programmed an R3k module using the clrfu and a USB adapter? The manual says using USB is an option, but I can't get it work. I usually get error, "Error reading bytes". I can communicate with the Rabbit using a USB adapter, just not reprogram it. Programming works fine using the serial port with the same set of cables. Commandline: clrfu .\myfile.bin -s 4:115200 -cl ...


Rabbit and USB

Started by Chris Smolinski in Rabbit-Semi12 years ago 1 reply

Has anyone looked into being able to communicate with USB devices using a Rabbit? That is, the Rabbit would be the host, not a USB ...

Has anyone looked into being able to communicate with USB devices using a Rabbit? That is, the Rabbit would be the host, not a USB device. While a general purpose interface might not be possible, I have one case now where I need to communicate with a USB device that uses an FTDI-245 interface chip (it appears on the PC as a serial port). What I would like to


RCM4000 and DLP-USB245M-G Integration.

Started by Boy Rabbit in Rabbit-Semi9 years ago 5 replies

Hello, I have the RCM4000 Dev. Board. and I have now DLP-USB245M-G** - USB FIFO Adapter Board and DLP-USB232M-G** - USB UART...

Hello, I have the RCM4000 Dev. Board. and I have now DLP-USB245M-G** - USB FIFO Adapter Board and DLP-USB232M-G** - USB UART Adapter Board My problem, I am trying to use USB interface rather than RSR232 serial port. I have the USB cable, I have DLP-USB245M-G but I am not that good in Hardwar:(. can you help me to interface the USB module to the developme...


Programming cable & USB

Started by Robert Horton in Rabbit-Semi11 years ago 3 replies

Ok, I now that Rabbit supply a USB-232 converter as a solution to the non existence of serial ports on recent computers. Wouldn't it be nice...

Ok, I now that Rabbit supply a USB-232 converter as a solution to the non existence of serial ports on recent computers. Wouldn't it be nice if the programming cable could have a native USB interface instead of 232. USB-232 converters are not all equal as I have found from my own experiments where some converters simply don't work with the RFU let alone running the development environme...


USB specailist in Korea

Started by afoofa in Rabbit-Semi13 years ago

Hi, We have immediate requirement for USB Device Stack based in Seoul Korea. 1)Skill: USB Device Stack/Host Stack developing...

Hi, We have immediate requirement for USB Device Stack based in Seoul Korea. 1)Skill: USB Device Stack/Host Stack developing experience Under Embedded System , USB Device Stack developing experience(necessary) (Making Device Stack by himself experinece) Diverse USB's Class developing experience(necessary) 2. Total exp: above 4~6+y


USB on RCM3200

Started by haider_karomi in Rabbit-Semi12 years ago 1 reply

Hello evry body, i want to connect USB interface to my Rabbit RCM3200. Has any body any idea or made that befor. what about serial usb...

Hello evry body, i want to connect USB interface to my Rabbit RCM3200. Has any body any idea or made that befor. what about serial usb converter moduls?? pls. help Thanke you


USB & Rabbit...

Started by Kevin Snow in Rabbit-Semi13 years ago 3 replies

Does anyone know of a simple way to add a USB port to a Rabbit controller? We're playing around with an idea that requires the Rabbit be...

Does anyone know of a simple way to add a USB port to a Rabbit controller? We're playing around with an idea that requires the Rabbit be able to control another device via USB. I didn't find much about it on the ZWorld website. Thanks. Kevin Snow kevin@kevi...


USB keyboard communication

Started by Arun Venkataswamy in Rabbit-Semi11 years ago 12 replies

Hi All, I want to connect an USB keyboard to the RCM3720. I am using an USB/PS2 convertor and the PS2KEYBOARD library (The PS2 connector...

Hi All, I want to connect an USB keyboard to the RCM3720. I am using an USB/PS2 convertor and the PS2KEYBOARD library (The PS2 connector connects to the RCM). When I connect a PS2 Keyboard with the circuit, the PS2KEYBOARD library works very well. When I connect the USB keyboard with USB/PS2 convertor to the circuit, I am not able to read the keys. When I set the debug option in the P...


USB-RS232 two-way communication

Started by Eric Chan in Rabbit-Semi12 years ago 1 reply

Hello, Does anyone know if ZWorld's USB-RS232 Converter Cable can establish 2-way communication? (i.e. it can do more than just...

Hello, Does anyone know if ZWorld's USB-RS232 Converter Cable can establish 2-way communication? (i.e. it can do more than just programming the Rabbit) I am working on a project and want to test USB-RS232 communication between my RCM3400 and a PC. My goal is to be able to read AND write data from both ends for processing. My


USB converter

Started by affa_3 in Rabbit-Semi10 years ago 3 replies

hi.. why does my DC 9.21 cannot open serial port using the rs232 to usb converter but i use direct pc com port to rs232 the DC 9.21 run...

hi.. why does my DC 9.21 cannot open serial port using the rs232 to usb converter but i use direct pc com port to rs232 the DC 9.21 run smoothly. what is the correct adjustment to connect RCM 3100 Prototyping board and DC 9.21 using USB converter


Information about USB interface with RCM3000 and RCM3200

Started by ko_f38 in Rabbit-Semi13 years ago

Dear sir, I'm very interested in the RCM3000 board with embedded Ethernet. I would like to know if somebody who works with your society...

Dear sir, I'm very interested in the RCM3000 board with embedded Ethernet. I would like to know if somebody who works with your society has already created an add-on board which would be able to manage a USB link between another device like another PC and the RCM3000 board. It would be better if the USB port is fixed on the board like your Ethern


how can I interface usb pen drive to rabbit processor?

Started by omprakash karamunge in Rabbit-Semi11 years ago 5 replies

Please tell me is it possible to design usb host controller? How can I read/ write the data in USB PEN DRIVE using rabbit processor. kindly...

Please tell me is it possible to design usb host controller? How can I read/ write the data in USB PEN DRIVE using rabbit processor. kindly reply soon. Thank you. regards, omprakash karamunge


Problems with PC-Rabbit communications for debbuging

Started by Francisco Garces in Rabbit-Semi12 years ago 3 replies

Hello, I got an USB/RS232 converter but I can't make it work with the Dynamic C (9.21). The cable is fine since I tried it on a different...

Hello, I got an USB/RS232 converter but I can't make it work with the Dynamic C (9.21). The cable is fine since I tried it on a different applicationĀ . I checked the box "Use USB to Serial converter" at the Project options window.... I've tried a lot but still doesn't works. Does anybody know anything about this problem? or has anyone worked out a usb/serial connec


programming via USB to serial converter?

Started by Hartmut Freihofer in Rabbit-Semi12 years ago 1 reply

hello, have ever somebody used a USB to serial converter to flash (program) a rabbit via the RFU? We have use several different...

hello, have ever somebody used a USB to serial converter to flash (program) a rabbit via the RFU? We have use several different converters, all with the same result: "timeout wile waiting for response from target". The switch "Use USB to serial converter" within the RFU utility also has no effect. We hav


USB port software needed.

Started by hughlatham69 in Rabbit-Semi13 years ago 1 reply

Looking for software to interface with a USB flash hard drive. Would like to know if anyone has a driver for sale. hugh latham ...

Looking for software to interface with a USB flash hard drive. Would like to know if anyone has a driver for sale. hugh latham


USB-to-Serial adapter

Started by Steve in Rabbit-Semi12 years ago 7 replies

Does anyone know the the models of USB-to-serial adapters that RabbitSemi recommends? I can't find any information on their web site. ...

Does anyone know the the models of USB-to-serial adapters that RabbitSemi recommends? I can't find any information on their web site. Steve


USB Programming Cable

Started by stan...@yahoo.com in Rabbit-Semi4 years ago

Just Wondering if anyone can confirm that the USB programming cables sold at Digi can be used on Dynamic C 9.25 Win 7 and BL2100? Thanks. ...

Just Wondering if anyone can confirm that the USB programming cables sold at Digi can be used on Dynamic C 9.25 Win 7 and BL2100? Thanks. Stan the man


PEN DRIVE WITH USB

Started by rafaelxprado in Rabbit-Semi12 years ago 1 reply

Dear friends, I'm build a application FTDI (USB-RS232) with Rabbit. In FTDI will connect a PEN DRIVE, but, don't know how to implement the ...

Dear friends, I'm build a application FTDI (USB-RS232) with Rabbit. In FTDI will connect a PEN DRIVE, but, don't know how to implement the protocol to comunicate my PEN DRIVE and my RABBIT, remenber that between this have a converter USB-RS232(FTDI chip). Any person have a ideia or documentation? Thanks, Rafael Prado - Brazil/SP