Simple question - does anyone know a supplier in the UK that sells the
female mating half of the connector used on the RCM3000 core module
(17x17 2mm IDC PCB mount socket). I can use either SMT or through hole
types, but through hole would be preffered.
RS, Farnell and Digikey dont do them in the no' of ways needed.
Thanks
Connectors
Started by ●August 11, 2005
Reply by ●August 11, 20052005-08-11
At 03:25 PM 8/11/2005 +0000, you wrote:
>
>Simple question - does anyone know a supplier in the UK that sells the
>female mating half of the connector used on the RCM3000 core module
>(17x17 2mm IDC PCB mount socket). I can use either SMT or through hole
>types, but through hole would be preffered.
>
>RS, Farnell and Digikey dont do them in the no' of ways needed.
If you're willing to live with the fact that you have to be careful when
you plug the Rabbitcore in, a 2x20 from 3M would work. We used that
solution before going direct to Rabbit and purchasing the correct sockets.
-Mike
>
>Simple question - does anyone know a supplier in the UK that sells the
>female mating half of the connector used on the RCM3000 core module
>(17x17 2mm IDC PCB mount socket). I can use either SMT or through hole
>types, but through hole would be preffered.
>
>RS, Farnell and Digikey dont do them in the no' of ways needed.
If you're willing to live with the fact that you have to be careful when
you plug the Rabbitcore in, a 2x20 from 3M would work. We used that
solution before going direct to Rabbit and purchasing the correct sockets.
-Mike
Reply by ●August 11, 20052005-08-11
We use Samtec connectors for this and have had no problems. The relevant
Samtec Part No.'s are:
Female SM Header MMS-117-02-L-DV
Male SM Header TMM-117-01-L-D-SM
Rich
----- Original Message -----
From: "Mike van Meeteren" <mike@mike...>
To: <rabbit-semi@rabb...>
Sent: Thursday, August 11, 2005 10:02 AM
Subject: Re: [rabbit-semi] Connectors > At 03:25 PM 8/11/2005 +0000, you wrote:
> >
> >Simple question - does anyone know a supplier in the UK that sells the
> >female mating half of the connector used on the RCM3000 core module
> >(17x17 2mm IDC PCB mount socket). I can use either SMT or through hole
> >types, but through hole would be preffered.
> >
> >RS, Farnell and Digikey dont do them in the no' of ways needed.
>
> If you're willing to live with the fact that you have to be careful when
> you plug the Rabbitcore in, a 2x20 from 3M would work. We used that
> solution before going direct to Rabbit and purchasing the correct sockets.
>
> -Mike > Yahoo! Groups Links >
Samtec Part No.'s are:
Female SM Header MMS-117-02-L-DV
Male SM Header TMM-117-01-L-D-SM
Rich
----- Original Message -----
From: "Mike van Meeteren" <mike@mike...>
To: <rabbit-semi@rabb...>
Sent: Thursday, August 11, 2005 10:02 AM
Subject: Re: [rabbit-semi] Connectors > At 03:25 PM 8/11/2005 +0000, you wrote:
> >
> >Simple question - does anyone know a supplier in the UK that sells the
> >female mating half of the connector used on the RCM3000 core module
> >(17x17 2mm IDC PCB mount socket). I can use either SMT or through hole
> >types, but through hole would be preffered.
> >
> >RS, Farnell and Digikey dont do them in the no' of ways needed.
>
> If you're willing to live with the fact that you have to be careful when
> you plug the Rabbitcore in, a 2x20 from 3M would work. We used that
> solution before going direct to Rabbit and purchasing the correct sockets.
>
> -Mike > Yahoo! Groups Links >
Reply by ●August 11, 20052005-08-11
Check out www.gradconn.com (they have a sales office in Ireland) and www.smp-tech.com
sudhir
From:
r...@yahoogroups.com [mailto:r...@yahoogroups.com]
On Behalf Of Richard Wayman
Sent: Thursday, August 11, 2005
1:51 PM
To:
r...@yahoogroups.com
Subject: Re: [rabbit-semi]
Connectors
We use Samtec connectors for
this and have had no problems. The relevant
Samtec Part No.'s are:
Female SM Header
MMS-117-02-L-DV
Male SM Header
TMM-117-01-L-D-SM
Rich
----- Original Message -----
From: "Mike van Meeteren"
<m...@fastec.com>
To:
<r...@yahoogroups.com>
Sent: Thursday, August 11, 2005 10:02
AM
Subject: Re: [rabbit-semi] Connectors
> At 03:25 PM 8/11/2005 +0000, you
wrote:
> >
> >Simple question - does anyone know
a supplier in the UK
that sells the
> >female mating half of the connector
used on the RCM3000 core module
> >(17x17 2mm IDC PCB mount socket). I
can use either SMT or through hole
> >types, but through hole would be
preffered.
> >
> >RS, Farnell and Digikey dont do
them in the no' of ways needed.
>
> If you're willing to live with the fact
that
you have to be careful when
> you plug the Rabbitcore in, a 2x20 from 3M
would work. We used that
> solution before going direct to Rabbit and
purchasing the correct sockets.
>
> -Mike
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
Reply by ●August 11, 20052005-08-11
While talking about connectors, does anyone know the connector to use
on a programming ribbon cable? For an RMC3200 programming port.
Thanks!
--- In rabbit-semi@rabb..., "Sudhir Murthy" <smurthy@t...> wrote:
> Check out www.gradconn.com <http://www.gradconn.com/> (they have a
sales
> office in Ireland) and www.smp-tech.com <http://www.smp-tech.com/>
>
> sudhir >
> _____
>
> From: rabbit-semi@rabb...
[mailto:rabbit-semi@rabb...] On
> Behalf Of Richard Wayman
> Sent: Thursday, August 11, 2005 1:51 PM
> To: rabbit-semi@rabb...
> Subject: Re: [rabbit-semi] Connectors >
> We use Samtec connectors for this and have had no problems. The
relevant
> Samtec Part No.'s are:
>
> Female SM Header MMS-117-02-L-DV
> Male SM Header TMM-117-01-L-D-SM
>
> Rich
>
> ----- Original Message -----
> From: "Mike van Meeteren" <mike@f...>
> To: <rabbit-semi@rabb...>
> Sent: Thursday, August 11, 2005 10:02 AM
> Subject: Re: [rabbit-semi] Connectors > > At 03:25 PM 8/11/2005 +0000, you wrote:
> > >
> > >Simple question - does anyone know a supplier in the UK that
sells the
> > >female mating half of the connector used on the RCM3000 core module
> > >(17x17 2mm IDC PCB mount socket). I can use either SMT or
through hole
> > >types, but through hole would be preffered.
> > >
> > >RS, Farnell and Digikey dont do them in the no' of ways needed.
> >
> > If you're willing to live with the fact that you have to be
careful when
> > you plug the Rabbitcore in, a 2x20 from 3M would work. We used that
> > solution before going direct to Rabbit and purchasing the correct
sockets.
> >
> > -Mike
> >
> >
> >
> >
> >
> > > Terms of Service. >
> _____
on a programming ribbon cable? For an RMC3200 programming port.
Thanks!
--- In rabbit-semi@rabb..., "Sudhir Murthy" <smurthy@t...> wrote:
> Check out www.gradconn.com <http://www.gradconn.com/> (they have a
sales
> office in Ireland) and www.smp-tech.com <http://www.smp-tech.com/>
>
> sudhir >
> _____
>
> From: rabbit-semi@rabb...
[mailto:rabbit-semi@rabb...] On
> Behalf Of Richard Wayman
> Sent: Thursday, August 11, 2005 1:51 PM
> To: rabbit-semi@rabb...
> Subject: Re: [rabbit-semi] Connectors >
> We use Samtec connectors for this and have had no problems. The
relevant
> Samtec Part No.'s are:
>
> Female SM Header MMS-117-02-L-DV
> Male SM Header TMM-117-01-L-D-SM
>
> Rich
>
> ----- Original Message -----
> From: "Mike van Meeteren" <mike@f...>
> To: <rabbit-semi@rabb...>
> Sent: Thursday, August 11, 2005 10:02 AM
> Subject: Re: [rabbit-semi] Connectors > > At 03:25 PM 8/11/2005 +0000, you wrote:
> > >
> > >Simple question - does anyone know a supplier in the UK that
sells the
> > >female mating half of the connector used on the RCM3000 core module
> > >(17x17 2mm IDC PCB mount socket). I can use either SMT or
through hole
> > >types, but through hole would be preffered.
> > >
> > >RS, Farnell and Digikey dont do them in the no' of ways needed.
> >
> > If you're willing to live with the fact that you have to be
careful when
> > you plug the Rabbitcore in, a 2x20 from 3M would work. We used that
> > solution before going direct to Rabbit and purchasing the correct
sockets.
> >
> > -Mike
> >
> >
> >
> >
> >
> > > Terms of Service. >
> _____
Reply by ●August 11, 20052005-08-11
At 12:05 AM 8/12/2005 +0000, you wrote:
>
>While talking about connectors, does anyone know the connector to use
>on a programming ribbon cable? For an RMC3200 programming port.
2x5 2mm spacing. Gotta have 1mm instead of .050 cable too.
-Mike
--
Mike vanMeeteren fast351@fast... FASTechnologies Corp.
Track Hauler: 2001 F150 Track toy: 89 Mustang LX 351W 10.93 @ 122.5 MPH
>
>While talking about connectors, does anyone know the connector to use
>on a programming ribbon cable? For an RMC3200 programming port.
2x5 2mm spacing. Gotta have 1mm instead of .050 cable too.
-Mike
--
Mike vanMeeteren fast351@fast... FASTechnologies Corp.
Track Hauler: 2001 F150 Track toy: 89 Mustang LX 351W 10.93 @ 122.5 MPH
Reply by ●August 12, 20052005-08-12
At 10:31 PM 8/11/2005, you wrote:
>At 12:05 AM 8/12/2005 +0000, you wrote:
> >
> >While talking about connectors, does anyone know the connector to use
> >on a programming ribbon cable? For an RMC3200 programming port.
>
>2x5 2mm spacing. Gotta have 1mm instead of .050 cable too.
I believe they are 1.27mm (0.050) connectors. You would need 0.025" cable.
The RCM3000 uses 2mm.
------------
| Scott G. Henion | shenion@shen... |
| Consultant | Stone Mountain, GA |
| SHDesigns | PGP Key 0xE98DDC48 |
|Rabbit Libs: http://www.shdesigns.org/rabbit/ |
------------ --
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.338 / Virus Database: 267.10.6/69 - Release Date: 8/11/2005
>At 12:05 AM 8/12/2005 +0000, you wrote:
> >
> >While talking about connectors, does anyone know the connector to use
> >on a programming ribbon cable? For an RMC3200 programming port.
>
>2x5 2mm spacing. Gotta have 1mm instead of .050 cable too.
I believe they are 1.27mm (0.050) connectors. You would need 0.025" cable.
The RCM3000 uses 2mm.
------------
| Scott G. Henion | shenion@shen... |
| Consultant | Stone Mountain, GA |
| SHDesigns | PGP Key 0xE98DDC48 |
|Rabbit Libs: http://www.shdesigns.org/rabbit/ |
------------ --
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.338 / Virus Database: 267.10.6/69 - Release Date: 8/11/2005
