USB Multilink

Started by marc...@yahoo.it in 68HC1211 years ago 18 replies

Hi. I have worked for about one year with the same USB Multilink. Yesterday I broke 2 USB Multilink suddenly: the cable became hot and after...

Hi. I have worked for about one year with the same USB Multilink. Yesterday I broke 2 USB Multilink suddenly: the cable became hot and after the blue light turn off. I\'d like to understand what happened... Can you help me? Thanks....


Does P&E MULTILINK load code to EEPROM?

Started by G in 68HC1212 years ago 1 reply

I use a Adapt9S12E128 board in a testing project. I am using Metrowerks Code Warrior - CW12V3.1. My code is working right when P&E MULTILINK...

I use a Adapt9S12E128 board in a testing project. I am using Metrowerks Code Warrior - CW12V3.1. My code is working right when P&E MULTILINK connected with a PC. However, system will be reseted at once when unpluging P&E MULTILINK. Advise please. Is P&E MULTILINK able to load code to EEPROM? Thanks


EVB9S12DP256 and USB Multilink

Started by jehenzeb2978 in 68HC1210 years ago

I have purchased EVB9S12DP256 and USB Multilink with standard code warrier edition. I have connect the USB multilink according to the...

I have purchased EVB9S12DP256 and USB Multilink with standard code warrier edition. I have connect the USB multilink according to the manual direction. Both lights are ON . I open the example project for EVB9S12DP256 give in codewarrier examples and try to run it then HIWAVE.exe become halt. Please guide me in this regard. Thanx Mian jehanzeb


Connecting to UF32 with P&E Multilink

Started by joss_scholten2000 in 68HC1212 years ago 10 replies

I've been trying to connect to a UF32 board with the P&E micro Multilink to the boards BDM. The multilink works fine with a C32 board I...

I've been trying to connect to a UF32 board with the P&E micro Multilink to the boards BDM. The multilink works fine with a C32 board I have, but no dice on the UF32.. any suggestions?


Debug & Programming

Started by Andrew Lohmann in 68HC1210 years ago 2 replies

Hi, I have been pursuing the same or similar problems for a number of years with programming HCS12Dx. We have a few parallel Multilink P&E...

Hi, I have been pursuing the same or similar problems for a number of years with programming HCS12Dx. We have a few parallel Multilink P&E BDM interfaces and a USB Multilink. We also have a Compod12. The Compod12 programs any HCS12 reliably but the Multilink only programs HCS12E reliably and HCS12D's for a limited period of time. After that the only the Compod12 will program HCS12D's ...


p&e micro usb multilink (usb-ml-12)

Started by Clayton in 68HC1212 years ago 1 reply

Well, I've had nothing but trouble from these things. I am on my 4th one. They just keep breaking. Do any of you guys know of an ...

Well, I've had nothing but trouble from these things. I am on my 4th one. They just keep breaking. Do any of you guys know of an alternative that is compareble to the multilink.


Adding P&E's USB Multilink build

Started by aerowesty2000 in 68HC1211 years ago

Hello, We are using Codewarrior 4 with Softec's 9S12xdp512 evaluation board for our development and have recently purchased a P&E USB...

Hello, We are using Codewarrior 4 with Softec's 9S12xdp512 evaluation board for our development and have recently purchased a P&E USB Multilink BDM. How can I add a build that uses the USB Multilink instead of the on-board BDM Softec uses? Eventually I have to drop the eval board and start downloading directly to our MCU boards (same processor). We now we have a simulator and softec ...


Need help in codewarrior P&E Multilink debugger

Started by lijie1116 in 68HC129 years ago

Hello All: I have a uc-os application in mc9s12d64,but one problem occured ,in codewarrior fullchip simulation mode ,after the instruction...

Hello All: I have a uc-os application in mc9s12d64,but one problem occured ,in codewarrior fullchip simulation mode ,after the instruction "RTI" executed,the SP address added 9,and PC register loaded the correct adress.but in codewarrior P&E Multilink debugger mode after the instruction "RTI" executed,the SP have no change,and the PC register rest to 0 .I don't know why in P&E Multilink...


CodeWorrier + Multilink has landed.

Started by Bruce McMillan in 68HC1214 years ago 8 replies

Well, it took some 12 months on & off, but I can now say that CodeWorrier + Multilink is a nice package. Since I suspect I'm...

Well, it took some 12 months on & off, but I can now say that CodeWorrier + Multilink is a nice package. Since I suspect I'm not the only lost soul out there, I thought I might relate what has happened to get it working. I remain unclear as to what the predominant problem


P&E Multilink on XP

Started by minliu2000 in 68HC1214 years ago 4 replies

I'm trying to use a P&E Micro Multilink Rev.B on Windows XP with software using P&E's unit_12z.dll. I didn't have any problems with...

I'm trying to use a P&E Micro Multilink Rev.B on Windows XP with software using P&E's unit_12z.dll. I didn't have any problems with it on NT, but it doesn't work at all on XP. I've tried different parallel port modes and settings with no success, but maybe it's the DLL? I


new BDM multilink

Started by Mr angel castillo in 68HC1213 years ago 12 replies

Hello i`m new in this list. i live in monterrey, mexico i have a new BDM multilink cable of PEMICRO Company i have...

Hello i`m new in this list. i live in monterrey, mexico i have a new BDM multilink cable of PEMICRO Company i have problems for conect a MC68hc912B32 with the software true-time simulator and real time debuger of code warrior. but


Codewarrior HC12 V1.2 and USB Multilink ML-12 Rev C.

Started by "Guillermo F. Molina" in 68HC1210 years ago 2 replies

Hi all, Did anyone know if it is any chance to use the Hiwave debugger of the (old!) Codewarrior V1.2 with the new USB Multilink (ML-12 Rev....

Hi all, Did anyone know if it is any chance to use the Hiwave debugger of the (old!) Codewarrior V1.2 with the new USB Multilink (ML-12 Rev. C )? Thanks in advance. Best regards, G.Molina


Question about Free Programmer for P&E Multilink

Started by a_ribero in 68HC1212 years ago

Hi there: I would like to know if there is a free (or low cost) programmer software that can be used with the P&E USB Multilink to...

Hi there: I would like to know if there is a free (or low cost) programmer software that can be used with the P&E USB Multilink to program HCS12 parts (let's say, in a low volume production environment) stand-alone (without having to rely on Code Warrior or other IDE's) Thanks. Alex


P&E Multilink

Started by Adrian Vos in 68HC1211 years ago 2 replies

Hi All, Related to my previous query when I was trying to work out what was going on. The S12DP256B project I am working on has a 4MHz...

Hi All, Related to my previous query when I was trying to work out what was going on. The S12DP256B project I am working on has a 4MHz crystal, and uses the PLL to put the bus speed up to the max 25MHz speed. I use metrowerks to develop and test code on this platform, and I use the P&E Parallel BDM Multilink to connect to the target. When I debug my code in the target, I can step thro...


Promlem with the MC9S12D64's PLL with USB Multilink

Started by shcaoyh in 68HC1212 years ago 1 reply

I use the P&E USB HCS08/HCS12 Multilink as the development tool, the target is the 80 pins MC9S12D64. This board is a simple circuit, I...

I use the P&E USB HCS08/HCS12 Multilink as the development tool, the target is the 80 pins MC9S12D64. This board is a simple circuit, I use a 16MHz quartz crystal with the Colpitts configuration. With the REFDV=1 and the SYNR=2, the CPU bus frequence is 24MHz. The PLL initialization application have a delay before switch the system clock


Problems programing flash on M68KIT912DP256 with BDM Multilink/Metrowerks

Started by djsimpson100 in 68HC1215 years ago 3 replies

Hi all, I am having problems programming the flash on the MC9S912DP256. I am using Codewarrior HC12 V1.2 and the P&E BDM...

Hi all, I am having problems programming the flash on the MC9S912DP256. I am using Codewarrior HC12 V1.2 and the P&E BDM Multilink which came with the Motorola M68KIT912DP256. If I load the Fibo Flash example, the debugger stalls at at the 60% mark in execu


Debuging with P&E USB MULTILINK & Codewarrior 3

Started by ra in 68HC1214 years ago 12 replies

Hello, While talking about P&E USB MULTILINK and debugging with ICD-12 in Codewarrior 3, would someone know a trick to...

Hello, While talking about P&E USB MULTILINK and debugging with ICD-12 in Codewarrior 3, would someone know a trick to facilitate stepping through "main" code without landing in interrupt driven background routines? (In C) For example, if there is a peri


PEmicro USB HCS08 / HCS12 Multilink - help needed

Started by Benny in 68HC1210 years ago 11 replies

Hi all I am using the PEmicro USB HCS08 / HCS12 Multilink unit for programming / debugging. The unit is working good with simple projects,...

Hi all I am using the PEmicro USB HCS08 / HCS12 Multilink unit for programming / debugging. The unit is working good with simple projects, but when I am trying to run the CW debugger using this unit connected to the target board, and the project includes several active interrupts like: SCI + 2x PWM , the device lose synchronization and I can't debug Did anyone knows how to handle it...


PPL, Multilink and Code Warrior

Started by Darren in 68HC1214 years ago 4 replies

Hi All, I am using Code Warrior and a DP256, once I enable the PPL in the startup code, the True Time Sim seems to loose...

Hi All, I am using Code Warrior and a DP256, once I enable the PPL in the startup code, the True Time Sim seems to loose the connection to the target. Is there a trick to changing the Multilink clock rate so that the True Time Sim will keep working.


Problem with EEPROM in MC9S12D64

Started by panalogic2 in 68HC129 years ago 1 reply

I am developing code for a hand-held product that uses the MC9S12D64 processor. The product uses the internal EEPROM to store a number of...

I am developing code for a hand-held product that uses the MC9S12D64 processor. The product uses the internal EEPROM to store a number of 4-byte calibration values, generated when the product is calibrated. I am using the PEMicro's Win32, PROG12Z and ICD12Z programs to author, program and debug the code, connecting to the BDM via PEMicro's Multilink USB Multilink interface. The code i...