2 x 16 LCD

Started by senghoetoh in BasicX8 years ago 2 replies

Hi, I new in this product. Can anyone tell me with a BX-24 development kit, is it possible to use a 2x16 LCD which is not from...

Hi, I new in this product. Can anyone tell me with a BX-24 development kit, is it possible to use a 2x16 LCD which is not from netmedia? I notice that for netmedia 2x16 LCD, it has a JP2 Pin RX for serial input which the 2x16 LCD I'm currently using does not have it. Will the 2x16 LCD I'm currently using able to receive and display text message from the BX-24? If able to can you pls prov...


Setting Relays on the LCD+...

Started by airmaledfw in BasicX14 years ago

For some reason, whenever I tell the LCD+ to set/reset any of the on- board relays by sending two bytes to the LCD+, 18 Decimal...

For some reason, whenever I tell the LCD+ to set/reset any of the on- board relays by sending two bytes to the LCD+, 18 Decimal followed by 1~255 Decimal, the LCD+ spits an 82 Decimal back at me. Now, in the LCD+ documentation it mentions that the first byte I send th


2 X 16 LCD will not show text

Started by hamk7fj in BasicX10 years ago 3 replies

A new 2 X 16 LCD lights up and seems to accept and process control codes for backlight and cpu reset but every attempt to send normal text...

A new 2 X 16 LCD lights up and seems to accept and process control codes for backlight and cpu reset but every attempt to send normal text fails. I can see the bits arriving at the LCD with a scope. I have copied sample software from web site. All settings are default (9600, reverse logic, etc). I am using pin 13 of the BX-24 to drive the LCD and have checked voltage level at the LCD...


Serial LCD problem

Started by Carlos Eduardo Alves Cardoso in BasicX11 years ago 5 replies

Hello y'all I've just started with BasicX and so far it's not very hard... However I've been having problems connecting the serial LCD. I...

Hello y'all I've just started with BasicX and so far it's not very hard... However I've been having problems connecting the serial LCD. I have a BX-24 and a development kit with a socket that connects the LCD's RX pin to pin number 5 in the BX-24. I've already went through all the LCD examples I could find and still haven't figured out to put it to work. Or even configure, for t...


LCD+

Started by mwaddell2 in BasicX14 years ago

I am trying to interface a keypad to the LCD+. I am using the example files or module files provided to use the LCD. I am having ...

I am trying to interface a keypad to the LCD+. I am using the example files or module files provided to use the LCD. I am having no problem writing to the LCD, just reading the keypad. I seem to be able to read the keypad as a port but not as just a serial input. I am trying to u


LCD+2 power connections

Started by Brian Little in BasicX12 years ago 1 reply

I have had a bad experience with using a Radio Shack power adapter (1.5V - 12 V 300mA) with the LCD+2 using the onboard female plug to ...

I have had a bad experience with using a Radio Shack power adapter (1.5V - 12 V 300mA) with the LCD+2 using the onboard female plug to the adapter. It burned out the board due to it supposedly putting out higher voltage than the 12V I had it set for. I purchased a replacement LCD+2. I am somewhat cautious about connecting power to the LCD+2. So I have three


Parallel LCD

Started by p_dubinsky in BasicX14 years ago 1 reply

Does anyone have any sample code for interfacing a BX24 to a parallel LCD, ie. a Seiko L2034 (4 X 20)? I've seen the LCD driver for...

Does anyone have any sample code for interfacing a BX24 to a parallel LCD, ie. a Seiko L2034 (4 X 20)? I've seen the LCD driver for the BX35 but I'm a bit confused about implementing this on the BX24. TIA, Paul


LCD+ Questions

Started by Conrad A***** in BasicX13 years ago

Hey guys I finally have found some time to experiment with my LCD+ hooked up to my BX24. I just came up with a project that will...

Hey guys I finally have found some time to experiment with my LCD+ hooked up to my BX24. I just came up with a project that will enable me to learn as much as possible about the LCD+ to BX24 interface. I plan on making a security system for my garage with a keypad to enter a p


Help Talking to LCD

Started by bsom21122 in BasicX12 years ago 3 replies

Well, I've gottan a few of thise LCD's from DOntronics in Australia and I'm trying to get them to talk to my BasicX's but I'm not having good...

Well, I've gottan a few of thise LCD's from DOntronics in Australia and I'm trying to get them to talk to my BasicX's but I'm not having good luck. I've tried Com1 and Com3, but I have been unable to get the screen to respond. If I use my Parallax USBtoSER, the screen works great. I'm stumped. I've used the serial LCD's from Parallax, et al. before, but this screen is more complicated...


Altimeter and LCD+ example code

Started by greatwitenorth in BasicX14 years ago 9 replies

Does anyone know of a web site with code for building and altimeter with the lcd+ and bx-24? Also if i needed to enter in new...

Does anyone know of a web site with code for building and altimeter with the lcd+ and bx-24? Also if i needed to enter in new numbers to my program thorugh a keypad hooked up to the lcd+ what would be the easiest way to do that? One digit is easy, just wait for it and assign it t


conflict of timer1

Started by Ashwin Sathyanarayanan in BasicX11 years ago

Dear all, I am using a LCD display using pins 5,6,7 & 9 to display on my LCD. And i a= m Using the input capture pin to measure display the...

Dear all, I am using a LCD display using pins 5,6,7 & 9 to display on my LCD. And i a= m Using the input capture pin to measure display the freq. I was wondering = if there is a conflict of the timer 1 by any chnace in these 2 functions. B= ecause i am not able to disply the required frequency on the LCD. Cab any o= ne please hwlp me out on this front. Thanks in advace. Regards, Ashwin O...


Graphics lcd panel

Started by nuepatrick in BasicX13 years ago 1 reply

Hello all, I just aquired this graphics lcd panel. The information on the back is as follows: convergent technologies display board ...

Hello all, I just aquired this graphics lcd panel. The information on the back is as follows: convergent technologies display board MPD or MPO 300 REV2:1669 Does anybody know anything about this display? The schematic I have showing that it is connected to a HD61830 LCD timing controller. Could this thing be used with


Newbie with EDE702/LCD question

Started by eldocountry in BasicX14 years ago

Hey guys, Please bear with me, I'm new to the BX series, but have a BX24 for a project I'm working on: a vacuum tube stereo...

Hey guys, Please bear with me, I'm new to the BX series, but have a BX24 for a project I'm working on: a vacuum tube stereo amp with LCD display and relay control. The problem is, the LCD is a 2x20 from bgmicro that uses the 4 bit data interface (sends two gro


[AD] Serial LCD Kits

Started by pha555 in BasicX14 years ago

I have recently finished developing two serial LCD kits which are powerful and quite reasonably priced; $4.95 and $5.95. These...

I have recently finished developing two serial LCD kits which are powerful and quite reasonably priced; $4.95 and $5.95. These are kits, suitable for assembly on a solderless breadboard. The kits do not include a PCB. The LCD #106 Kit provides an interface between a Mic


hi grup

Started by mehdy_jadidy2 in BasicX12 years ago 1 reply

hi grup i need libreries/example code for t6963 lcd for atmega16 micro in basic or C i need to draw lines , put pixels and put text on...

hi grup i need libreries/example code for t6963 lcd for atmega16 micro in basic or C i need to draw lines , put pixels and put text on lcd (my lcd dont have CD pin but have a pin with name "RS" i think thats similar) i use bascom example but it dosnt work thanks for the replies. regards


LCD from a Digital Camera

Started by holopoint.rm in BasicX14 years ago

I have a small LCD from a digital camera. "Casio A 1026" is written on it. Anyone has experience with interfacing with something...

I have a small LCD from a digital camera. "Casio A 1026" is written on it. Anyone has experience with interfacing with something like this ? I tried to find the Datasheet or spec for this LCD, without success. Anyone knows where to find this information? Thank


Anyone succeeded with KS0713 LCD interface ?

Started by gpsrunner2000 in BasicX14 years ago 3 replies

Hi members Try to connect LCD KS0713 controller in serial mode to my BASICX-24. (I use SID, RS, SCLK without any Pull Up...

Hi members Try to connect LCD KS0713 controller in serial mode to my BASICX-24. (I use SID, RS, SCLK without any Pull Up resistors) ANYONE know of any BASICX-24 codes somewhere that works? Modified "LCD_595 by Jon Williams over and over" but the LCD


Keypad missing...

Started by Alex Chaihorsky in BasicX12 years ago 4 replies

I bought several days ago the LCD+2 Development Kit and when it came the Keypad was missing. I left a message on BASICX sales machine last ...

I bought several days ago the LCD+2 Development Kit and when it came the Keypad was missing. I left a message on BASICX sales machine last Friday but nobody called back. This is what the description said: "Development kit contains everything you need to start developing with LCD+2. Kit includes; 1 LCD+2 Display, 16 key keypad and interconnect cabl


Re: LCD

Started by Niel Jepsen in BasicX14 years ago 5 replies

I have hooked up an LCD and keyboard a la the LCD users guide, but the keyboard options on pg 6 table 1 don't seem totally kosher. ...

I have hooked up an LCD and keyboard a la the LCD users guide, but the keyboard options on pg 6 table 1 don't seem totally kosher. Firstly, I presume the table 1 heading "mode byte" should read "mode bit" Secondly, setting b1 to 1 or 0 has no effect with me. Both


FA: 8 line by 20 column LCD

Started by Don Kinzer in BasicX14 years ago 6 replies

I have put up for auction on eBay an 8x20 serial LCD that is surplus to my needs. Item #4120316584. This is the same model of...

I have put up for auction on eBay an 8x20 serial LCD that is surplus to my needs. Item #4120316584. This is the same model of LCD that I used in my dividing head controller. http://www.kinzers.com/don/BX24/Indexer