
How to Build a Fixed-Point PI Controller That Just Works: Part I
This two-part article explains five tips to make a fixed-point PI controller work well. I am not going to talk about loop tuning -- there are hundreds of articles and books about that; any control-systems course will go over loop tuning enough to help you understand the fundamentals. There will always be some differences for each system you have to control, but the goals are the same: drive the average error to zero, keep the system stable, and maximize performance (keep overshoot and delay...
Embedded Software Creation II - European Normative & Legislation
In this post I will explain the European Normative. I will answer the main questions and I will be open to answer all the doubts any of you could have. Please leave a comment and I will answer if i could.
Why I need to look and accomplish some standards?The main reason is if you want to comercialize the product in the European Union, if exists any European Directive that cover the product, the product must be marked with the CE mark. For USA it work in the same way by the...
C++ on microcontrollers 4 – input pins, and decoding a rotary switch
This blog series is about the use of C++ for modern microcontrollers. My plan is to show the gradual development of a basic I/O library. I will introduce the object-oriented C++ features that are used step by step, to provide a gentle yet practical introduction into C++ for C programmers. Reader input is very much appreciated, you might even steer me in the direction you find most interesting.
So far I...
C++ on microcontrollers 3 – a first shot at an hc595 class with 8 output pins
This blog series is about the use of C++ for modern microcontrollers. My plan is to show the gradual development of a basic I/O library. I will introduce the object-oriented C++ features that are used step by step, to provide a gentle yet practical introduction into C++ for C programmers. Reader input is very much appreciated, you might even steer me in the direction you find most interesting.
In the first part of...
C++ on microcontrollers 2 - LPCXpresso, LPC-link, Code Sourcery, lpc21isp, linkerscript, LPC1114 startup
previous parts: 1
This blog series is about the use of C++ for modern microcontrollers. My plan is to show the gradual development of a basic I/O library. I will introduce the object-oriented C++ features that are used step by step, to provide a gentle yet practical introduction into C++ for C programmers. Reader input is very much appreciated, you might even steer me in the direction you find most interesting.
I teach my students that...
Using XML to describe embedded devices (and speak to them)
This article discusses one of the typical development cycles in embedded device and communication design and presents a possible, light weight solution using the free DClib/netpp framework.
The challengeAssume we're faced with the design of an embedded device, be it a simple SoC unit or a more complex, uC controlled engine with various attached peripherals. From first prototype to the market, the following development cycle is typically walked through:
C++ on microcontrollers 1 - introduction, and an output pin class
This blog series is about the use of C++ for modern microcontrollers. My plan is to show the gradual development of a basic I/O library. I will introduce the object-oriented C++ features that are used step by step, to provide a gentle yet practical introduction into C++ for C programmers. Reader input is very much appreciated, you might even steer me in the direction you find most interesting.
I am lazy. I am also a programmer. Luckily, being a lazy...
Which MOSFET topology?
A recent electronics.StackExchange question brings up a good topic for discussion. Let's say you have a power supply and a 2-wire load you want to be able to switch on and off from the power supply using a MOSFET. How do you choose which circuit topology to choose? You basically have four options, shown below:
From left to right, these are:
High-side switch, N-channel MOSFET High-side switch, P-channel MOSFET Low-side switch, N-channel...Kind of Buggy! The state machine fantastic//
Over the years, I have had the opportunity to experience a lot of different kinds of coding mistakes. There were many that most programmers are familiar with, counting errors, indexing errors (the infamous 'off by one' bug), memory space sharing errors (A threading issue) as well as numerous others. I ran into one recently that I wound up using an old trick to help find.
My current project is a Pan/Tilt camera that was, upon occasion, not homing properly in one axis. The camera is a...
Deeply embedded design example - Logic replacement
I have always believed that some of the low-cost, low-pin count, low-resource microprocessors would make an excellent choice for the replacement of discrete logic components. In these cases the deeply embedded microprocessor would become less of a general purpose computer and more of a logic replacement, providing a prescribed function with no connection to the outside world. In a world of bigger, faster and more expensive, it is a pleasant change of pace...
NXP LPC17xx/40xx: Decoding the Part ID
This is the first blog of a number dealing with the NXP LPC17xx/40xx processor families and how to program them despite the lack of documentation. The next blog will deal with implementing the LPC17xx/40xx UART with interrupts properly, and a subsequent blog will show how to use the UART in RS485 Normal Multidrop Mode (NMM) with Auto Address Detection (AAD).
My company has decided on using the NXP LPC17xx/40xx processor line for all our embedded projects. Since...
When a Mongoose met a MicroPython, part I
This is more a framework than an actual application, with it you can integrate MicroPython and Cesanta's Mongoose.
Mongoose runs when called by MicroPython and is able to run Python functions as callbacks for the events you decide in your event handler. The code is completely written in C, except for the example Python callback functions, of course. To try it, you can just build this example on a Linux machine, and, with just a small tweak, you can also run it on any ESP32 board.
MSP430 LaunchPad Tutorial - Part 3 - ADC
In this new episode of our journey into MSP430 I will explain the basics of Analog to Digital Conversion on the MSP430G2231.We will write a program that will read an ADC channel and will toggle some leds based on the result of the conversion.
We start as usual with the inclusion of the header file for the MSP430G2231, the leds stuff and with the definition of a variable that will store the result of the conversion. We also declare a function that will initialize the ADC...
C++ on microcontrollers 3 – a first shot at an hc595 class with 8 output pins
This blog series is about the use of C++ for modern microcontrollers. My plan is to show the gradual development of a basic I/O library. I will introduce the object-oriented C++ features that are used step by step, to provide a gentle yet practical introduction into C++ for C programmers. Reader input is very much appreciated, you might even steer me in the direction you find most interesting.
In the first part of...
Deeply embedded design example - Logic replacement
I have always believed that some of the low-cost, low-pin count, low-resource microprocessors would make an excellent choice for the replacement of discrete logic components. In these cases the deeply embedded microprocessor would become less of a general purpose computer and more of a logic replacement, providing a prescribed function with no connection to the outside world. In a world of bigger, faster and more expensive, it is a pleasant change of pace...
Arduino robotics #4 - HC-SR04 ultrasonic sensor
Arduino RoboticsArduino robotics is a series of article chronicling my first autonomous robot build, Clusterbot. This build is meant to be affordable, relatively easy and instructive. The total cost of the build is around $50.
1. Arduino robotics - motor control2. Arduino robotics - chassis, locomotion and power3. Arduino robotics - wiring, coding and a test run4.Designing Embedded Systems with FPGA-2
In last part, we created hardware design of basic system. The next step is to generate (compile) hardware design. Compiled hardware design is known as bit-stream andstored in *.bit file. To compile hardware, use hardware->generate hardware tab. The complete hardware design generation takes several seconds to several minutes depending on computer speed and design complexity. In back ground, the whole design process involves many different steps including synthesis, placement, routing and...
How to Arduino - a video toolbox
I've begun producing a new series of video tutorials for the hobbyist new to the Arduino or microcontrollers in general. My videos are very pragmatic - I prefer to answer the question "what is the quickest, simplest and most affordable way to accomplish this?". The videos are meant to be a quick source of "how to" knowledge for the hobbyist that is using an LCD display, ultrasonic sensor or accelerometer for the first time, for example. I hope you enjoy this series of...
Bellegram, a wireless DIY doorbell that sends you a Telegram message
A wireless button that uses the M5 STAMP PICO and Mongoose to send a Telegram message when pressed. The code is written in C
Arduino robotics #3 - wiring, coding and a test run
Arduino RoboticsArduino robotics is a series of article chronicling my first autonomous robot build, Clusterbot. This build is meant to be affordable, relatively easy and instructive. The total cost of the build is around $50.
1. Arduino robotics - motor control2. Arduino robotics - chassis, locomotion and power3. Arduino robotics - wiring, coding and a test run4.C++ on microcontrollers 3 – a first shot at an hc595 class with 8 output pins
This blog series is about the use of C++ for modern microcontrollers. My plan is to show the gradual development of a basic I/O library. I will introduce the object-oriented C++ features that are used step by step, to provide a gentle yet practical introduction into C++ for C programmers. Reader input is very much appreciated, you might even steer me in the direction you find most interesting.
In the first part of...
Designing Embedded Systems with FPGA-2
In last part, we created hardware design of basic system. The next step is to generate (compile) hardware design. Compiled hardware design is known as bit-stream andstored in *.bit file. To compile hardware, use hardware->generate hardware tab. The complete hardware design generation takes several seconds to several minutes depending on computer speed and design complexity. In back ground, the whole design process involves many different steps including synthesis, placement, routing and...
An Introduction to Embedded Development
This blog is a series to provide an introduction to embedded development for the aspiring embedded developer. No prior embedded development experience will be assumed, but you should have a reasonable understanding of the C language and knowledge of basic electronics. It will focus on the TI MSP430, but present topics in a generic way that can be easily translated to other processors. Welcome!Hello, and welcome to my blog! This blog will be somewhat different from most...
Five Embedded Linux Topics for Newbies !
Are you an embedded systems enthusiast looking to broaden your horizons with embedded Linux? explore those 5 topics.
Motion Sensor with Raspberry Pi and MPU6050 - Part 1
This blog will help you build your own, low cost 3-axis motion sensor using Raspberry Pi and Invensense MPU6050.
NXP LPC17xx/40xx: Decoding the Part ID
This is the first blog of a number dealing with the NXP LPC17xx/40xx processor families and how to program them despite the lack of documentation. The next blog will deal with implementing the LPC17xx/40xx UART with interrupts properly, and a subsequent blog will show how to use the UART in RS485 Normal Multidrop Mode (NMM) with Auto Address Detection (AAD).
My company has decided on using the NXP LPC17xx/40xx processor line for all our embedded projects. Since...
Making a connection 1
In order for your system to control devices, you must be able to connect it to those devices.
Besides different sizes based on wire size, there are a few different styles of connectors that can be used. There are also weather-resistant terminals that can be used if needed.
Ring
(Parks, 16)
- used for circuits that you don’t want to become easily disconnected
- ground wire attached to a stud
Push-On
- can be used on relay terminals
(Parks, 18)
- could be...
nRF5 to nRF Connect SDK migration via DFU over BLE
This writeup contains some notes on how I was able to migrate one of my clients projects based on the nRF5 SDK, to nRF Connect SDK (NCS) based firmware, via a DFU to devices in the field over BLE.
LCD Control with an MCU
Controlling a liquid crystal display (LCD) to indicate a few ASCII characters should not be a big challenge as a project. That’s exactly what I thought when I decided to include a 2 line by 16 character display in my current project. My initial thought was. “How difficult could it be with all the resources on the internet and my embedded development expertise primarily in telecoms?” Let me tell you it is not as straightforward as I thought it would be and therefore I...
Getting Started with (Apache) NuttX RTOS Part 2 - Looking Inside and Creating Your Customized Image
In the previous article (https://www.embeddedrelated.com/showarticle/1524.p...) we saw how to run NuttX RTOS using the SIMulator. Today we will see how NuttX's directory tree is organized and how to use the menuconfig to enable some applications, including some tricks to search and solve dependencies.
NuttX Directories organization:
If you have previously compiled the Linux kernel or the U-Boot bootloader you will see that the NuttX source tree organization is...
