Forums Search for: AT91RM9200
AT91RM9200
inHi Someone asked me to help him with AT91RM9200 and AT91RM9200-EK kit. I have gnu toolchain with gcc "3.4.3". I plan that we will run programs...
Hi Someone asked me to help him with AT91RM9200 and AT91RM9200-EK kit. I have gnu toolchain with gcc "3.4.3". I plan that we will run programs directly on that processor - without any kind of operating systems (linux or winCE). I'm looking for project samples for this board. Are there in the internet available any project free samples? I need informations about memory addressing - whe...
Problem Porting nucleus onto AT91RM9200
inHi, I am trying to port Nucleus Kernel onto the AT91RM9200 Target (on Cogent CSB337) using Nucleus EDGE IDE. I am facing some problem with the...
Hi, I am trying to port Nucleus Kernel onto the AT91RM9200 Target (on Cogent CSB337) using Nucleus EDGE IDE. I am facing some problem with the Stack handling especially while servicing the interrupts. Has anyone been able to successfully prot Nucleus RTOS onto AT91RM9200? Please let me know. Thanks and Regards, Prashanth
PS/2 to Serial\SPI converter?
inHi, Im working on building a dev board based on the AT91rm9200. I have based this design on the AT91rm9200-DK for reference. Im trying to...
Hi, Im working on building a dev board based on the AT91rm9200. I have based this design on the AT91rm9200-DK for reference. Im trying to add a keyboard to this board, but this has been hampered by the non-availability of the chip thats used to convert the PS/2 data to serial or SPI on the AT91rm9200-DK, the UR6HCPS2-SP40. Does anyone know any alternative to this particular chip? If yes,...
SPI Data Flash using with AT91RM9200 208pin
inHi, I'm trying to build a system using AT91RM9200 208pin (Linux) and I would greatly appreciate anyone share his experiance on using just SPI Data...
Hi, I'm trying to build a system using AT91RM9200 208pin (Linux) and I would greatly appreciate anyone share his experiance on using just SPI Data Flash like AT45DB642 on AT91RM9200 208pin without using other kind of memory on Linux
AT91RM9200 and 16-bit SDRAM not working
inHello All, I am trying to get a 16-bit SDRAM (MT48LC16M16A2-75) to work with the AT91RM9200 and no matter what I try, it fails to work...
Hello All, I am trying to get a 16-bit SDRAM (MT48LC16M16A2-75) to work with the AT91RM9200 and no matter what I try, it fails to work properly: Hardware connections: AT91RM9200 MT48LC16M16A2 ---------- ------------- D0-15 DQ0-15 A2-A11 A0-A9 SDA10 A10 A13-A14 A11-A12 BA0/1 BA0/1 SDCKE CKE SDCK CLK \BS0/1 DQML/H \RAS \RAS \...
AT91RM9200 compiler
inHi everybody: I'm looking for AT91RM9200's compiler C & I searched so many.I have found different companies for this purpose like: HI-TECH &...
Hi everybody: I'm looking for AT91RM9200's compiler C & I searched so many.I have found different companies for this purpose like: HI-TECH & Rowley Associates & Green Hills,but as a matter of fact I am so confused,I don't know how to compare them & which one of them is the best for my project. Can anybody please guide me? Thanks.
AT91RM9200 USB Mass Storage Device BULK Design
inHi,Members! I am looking for source code that will allow an embedded device to look like an USB mass storage device when inserted into a host...
Hi,Members! I am looking for source code that will allow an embedded device to look like an USB mass storage device when inserted into a host PC. The embedded device has an ARM core, the CPU in particular is an Atmel AT91RM9200, and will be using embedded Linux as its OS. Anyone give me some advices about how can i modify the example AT91RM9200-BasicUSB(CDC class) to Mass Storage Device cl...
Audio on AT91RM9200 under Linux
inHi, Has anyone had experience using audio on the AT91RM9200 under Linux? I was thinking of using the AC97 codec used (but not populated!) on...
Hi, Has anyone had experience using audio on the AT91RM9200 under Linux? I was thinking of using the AC97 codec used (but not populated!) on the DK board design. I only need mono. Thanks in advance for any help. Regards, Paul.
AT91RM9200- SDRAM interface
inHi, Can anyone explain why the address line A14 from AT91RM9200 is connected to NC pin of SDRAM (MT48LC8M16A2)? (reference:...
Hi, Can anyone explain why the address line A14 from AT91RM9200 is connected to NC pin of SDRAM (MT48LC8M16A2)? (reference: AT91RM9200ek-userguide, SDRAM interface section) Thanks S Mahesh.
at91rm9200---- Mass Storage Device application
inHi Can someone tell me if how can i implement My AT91RM9200 as an Mass storage device. If connected to the PC it shold be detected as a pen...
Hi Can someone tell me if how can i implement My AT91RM9200 as an Mass storage device. If connected to the PC it shold be detected as a pen drive. or can someone send me the link for the code shub005@yahoo.co.in regards santosh
at91rm9200 sd card performance
inHello, I have couple of questions in my head before buying an ev board.. Does anybody knows at91rm9200 sd card read/write...
Hello, I have couple of questions in my head before buying an ev board.. Does anybody knows at91rm9200 sd card read/write performance? Does AT91rm9200 uses 4 wire sd mode or only 1 wire spi mode? what is maximum sd card erad/write performance when programming in assembly and C ? What is maximum performance of uclinux sd card drivers? (Are sd drivers from uclinux or uboot?) Thank...
SDRAM memory width with Atmel AT91RM9200
inWe are designing a microcomputer based on the Atmel AT91RM9200 controller. We are gong to give it 128Mb of SDRAM, 4M X 32. I am trying to decide...
We are designing a microcomputer based on the Atmel AT91RM9200 controller. We are gong to give it 128Mb of SDRAM, 4M X 32. I am trying to decide whether to use 2 x 4M x 16 or 1 x 4M x 32. The reference design uses 16 bit wide memories, which appear to be slightly cheaper than the equivalent 32 with perhaps more manufactureres. What do people feel, what are the advantages of each, easier layo...
PHY for AT91RM9200 ?
inJust beginning a new design here, built on the AT91RM9200. I am searching for RoHS-compliant components that will be available now and hopefully...
Just beginning a new design here, built on the AT91RM9200. I am searching for RoHS-compliant components that will be available now and hopefully well into the future. First up is a enet PHY. AMD says that they have successfully tested these PHY chips: Intel LXT971A, Davicom DM9161E, AMD Am79C874. However, the chip that seems to be most readily available (and low power) is the National DP...
AT91RM9200 linux woes
inOk So Im to the point I dont know what to try next. Im trying to bring my custom AT91RM9200 board to life. I have 16MB of SDRAM on CS0 (starting...
Ok So Im to the point I dont know what to try next. Im trying to bring my custom AT91RM9200 board to life. I have 16MB of SDRAM on CS0 (starting at 0x20000000 ending at 0x21000000) and 2MB of data flash at 0xC0000000. First step was getting uBoot running. Which for some reason if I stick uBoot (1.1.4) as resident and try and let it relocate itself it wont run, no serial output. So I stuck with t...
AT91RM9200 low voltage SDRAM...
inHello, Is it possible to use a low voltage (1.8V) SDRAM chip with the AT91RM9200? All the schematics i've seen or the finished boards uses...
Hello, Is it possible to use a low voltage (1.8V) SDRAM chip with the AT91RM9200? All the schematics i've seen or the finished boards uses 3.3V ones. Regards, Arek
Flash Interface with AT91RM9200
inHi, I am doing a prototype baord based on AT91RM9200.I am planning to use Intel Strataflash memory (E28F640J3A)on the board.This flash memory...
Hi, I am doing a prototype baord based on AT91RM9200.I am planning to use Intel Strataflash memory (E28F640J3A)on the board.This flash memory is having a program enable input.How can i connect this to the processor, while interfacing?If anyone is using the same flash, please suggest. Also I would like to understand how does the USB_DP_PUP signal enable/disable the pull-up resistor on DP?(Re...
problem porting linux to AT91RM9200 board
inHi , Im trying to port linux to a custom board i designed (based on the AT91RM9200 ). But im faced with a problem - after the execution of...
Hi , Im trying to port linux to a custom board i designed (based on the AT91RM9200 ). But im faced with a problem - after the execution of the kernel is started , at the very first instruction , i get an invalid instruction message ( which further prints all the register values) ..what could be the reason for such an error? Further , what other Free Operatign systems are avaliable that ...
AT91RM9200 and AC97 codec - not recommended ?
inHi everybody. I'm finishing my RM9200 board (32MB SDRAM, 2MB SPI NOR, Smart Media, RTL8201). Now I need to choose te audio interface. First -...
Hi everybody. I'm finishing my RM9200 board (32MB SDRAM, 2MB SPI NOR, Smart Media, RTL8201). Now I need to choose te audio interface. First - I was thinking about AC97 codec - like National's LM4549 because I saw this chip in some RM9000 SDK boards. But I saw some posts with information that AT91RM9200 and its SSC doesn't work with AC97 codec. Can somebody confirm (or better not ;) ) t...
Problems with programming AT91RM9200
inhi, I have designed board with AT91RM9200 microcontroller and I've got some problems with programming it... I wanted to program any bootloader...
hi, I have designed board with AT91RM9200 microcontroller and I've got some problems with programming it... I wanted to program any bootloader into connected AT45DB041D dataflash. Right now I can't send data via DBGU - I thought it is MAX3232's fault but I replaced it and still nothing. However sending data from ARM to PC works ok. Instead of programming dataflash with xmodem I tried to do it th...
RFC: "Comet" board with AT91RM9200
inHello, we are designing a microcomputer named "Comet" based on the Atmel AT91RM9200 controller. All design files and software will be...
Hello, we are designing a microcomputer named "Comet" based on the Atmel AT91RM9200 controller. All design files and software will be licensed under the GPL. Currently the schematics is all what we have. We probably packed too much building blocks into the design. Before we cut down the design and start building the PCB it would be nice to hear what you think which optional building blo...