Hello, I am using XDS510 USB emulator. I am able to reset my emulator but unable to detect it. Getting below error in sdconfig **...

Hello, I am using XDS510 USB emulator. I am able to reset my emulator but unable to detect it. Getting below error in sdconfig ** Checking for a valid emulator/eZdsp $$ You are connected to: $$ EmuProductName=XDS510USB $$ EmuPortAddr=0x510 $$ EmuPortMode=USB $$ ProductId=510 $$ ProductVersion=84 ** Checking emulator/eZdsp scan connection ** Emulator Test ** ...

I can't connect to a PDS51 (with serial cable), the software says that there is no emulator connected to the COM port!!! Is there anybody...

I can't connect to a PDS51 (with serial cable), the software says that there is no emulator connected to the COM port!!! Is there anybody that knows this emulator? I need help... Thanks

Hi, I am using a JTAG based emulator, but as I could see the JTAG emulator can not give what we want when we are looking for very complex...

Hi, I am using a JTAG based emulator, but as I could see the JTAG emulator can not give what we want when we are looking for very complex bugs, it has a limited trace buffer and we can not set watch pointers, etc... The conclusion is that we have to have a better tool, but it is being difficult to find something out there, what amazing me, because the PXA is largelly used. I thought in...

I'm goint to debug ARM7TDMI using TI XDS510PP-Plus JTAG emulator. I want to know if it is possible to use XDS510 JTAG emulator under ADS(Arm...

I'm goint to debug ARM7TDMI using TI XDS510PP-Plus JTAG emulator. I want to know if it is possible to use XDS510 JTAG emulator under ADS(Arm Development Suite) environment. Do I need some drivers? Please, Help me.

Hi, I am trying to find a JTAG emulator for a new project which uses a ARM7 processor. I am considering several vendors, such as...

Hi, I am trying to find a JTAG emulator for a new project which uses a ARM7 processor. I am considering several vendors, such as Lauterbach (Trace32 ICD), Macraigor (Wiggler, Raven, usbDemon, mpDemon), Emutec (DebugJet), Hitex (Tantino), Embest, Nohau, EPI, SigNum, ...etc. The emulator has to support multi-core. If anyone has use the JTAG emulator from these vendors, can you pleas...

I have a board using a 25MHz 80C186EB and I'm looking for an in circuit emulator that will allow the following: Stepping through codestream...

I have a board using a 25MHz 80C186EB and I'm looking for an in circuit emulator that will allow the following: Stepping through codestream instruction by instruction That is it. I want to yank the CPU off the nonfunctional board, drop a socket, hook up the emulator and step through exactly what the on board CPU was seeing instruction by instruction. ...and the cheaper the better. ...

I would like to rent or buy (1 month period) an in-circuit emulator for the Intel 80C186XL processor. I need it for about 1 month. Doers someone...

I would like to rent or buy (1 month period) an in-circuit emulator for the Intel 80C186XL processor. I need it for about 1 month. Doers someone have one they could rent me or sell or could you refer me to a company that carries them. The manufacturer of the emulator is unimportant. thank you

Hi I am new to ARM. I have a aac decoder which i run in arm. It is working fine and it is perfectly matching. But the performance...

Hi I am new to ARM. I have a aac decoder which i run in arm. It is working fine and it is perfectly matching. But the performance numbers between simulator and emulator differs widely. In Simulator it is around 20Mcycles. But when i run the same in emulator it takes around 10 to 20 times higher with catch enable. As a test I tried a single load from same location for 100 times and on ave...

Hi, Where can I get a atmel 89c52 emulator ,or development kit, with a reasonable price? Thanks, Pipi

Hi, Where can I get a atmel 89c52 emulator ,or development kit, with a reasonable price? Thanks, Pipi

Hi, I am looking for a low cost 27xxx eprom emulator. Please advice me on which one I should get. Thanks Nathan

Hi, I am looking for a low cost 27xxx eprom emulator. Please advice me on which one I should get. Thanks Nathan

Hi , I am looking for a Renesas M16c/M32C M3A-0665 FoUSB emulator I know it has been superseded by the E8A but for particular reasons we...

Hi , I am looking for a Renesas M16c/M32C M3A-0665 FoUSB emulator I know it has been superseded by the E8A but for particular reasons we need the M16c/M32C M3A-0665 FoUSB emulator and it's software. renesas do not have any left. I have tried them so if any one, preferably UK based has a M16c/M32C M3A-0665 FoUSB emulator I could buy beg, borrow, steal or swap for an E8a please con...

Hi, for maintainance of a 68000 PLCC or DIP based board I'm looking to get an emulator or something else to load my code quickly into RAM....

Hi, for maintainance of a 68000 PLCC or DIP based board I'm looking to get an emulator or something else to load my code quickly into RAM. Sorry, I can't use any ROM monitor solutions since I don't know less about resource occupation. Even a used part and any hint where to get it is appreciated. Klaus

Please suggest good emulator for 8051/8052 which support ISP devices(Atmel AT89S series) Thanks Naimesh

Please suggest good emulator for 8051/8052 which support ISP devices(Atmel AT89S series) Thanks Naimesh

Hello, Its time for an EPROM emulator. I would prefer USB, > 1MBit, fast down load, Win2k/XP compatible tools,

Hello, Its time for an EPROM emulator. I would prefer USB, > 1MBit, fast down load, Win2k/XP compatible tools,

I have googled for an hour now, but the i386EX family does not seem to have a jtag emulator/debugger available. Is this true ?? hamilton

I have googled for an hour now, but the i386EX family does not seem to have a jtag emulator/debugger available. Is this true ?? hamilton

I need to find an emulator or some other way to support an old 80c51fa product. I already have an assembler (an old Avocet ava51.exe) that works...

I need to find an emulator or some other way to support an old 80c51fa product. I already have an assembler (an old Avocet ava51.exe) that works ok. I need a way to step through this code and see the source code and symbols. What is the best way to do this? The program is written only in assembly language. thanks, Walter

So if I was to think about writing an arm emulator for fun, which core family should I choose? I see that there are rt system and...

So if I was to think about writing an arm emulator for fun, which core family should I choose? I see that there are rt system and application cores (and secure). The benefits of each in terms of application are obvious. Are the rt systems averse to letting you write an operating system on top? thanks Sohail

Does anyone have an emulator for a 2716 eprom that they no longer have a use for? In the alternative, does anyone know if anyone is still making...

Does anyone have an emulator for a 2716 eprom that they no longer have a use for? In the alternative, does anyone know if anyone is still making these? Thanks. Tim

I need to run a couple of powerpc routines through an emulator to see what funky conversions are happening. Ive googled around and cant find...

I need to run a couple of powerpc routines through an emulator to see what funky conversions are happening. Ive googled around and cant find a stock C source tree i can compile and use. Preperably without much in the way of os support, just raw emulation. Any ideas? joolz -- --------------------------------- --- -- - Posted with NewsLeecher v6.5 Beta 2 Web @ http://www.new...

What I mean by a software emulator is, an application that runs on a desktop/laptop where some favor of MSP430 code can be run and tested, as if...

What I mean by a software emulator is, an application that runs on a desktop/laptop where some favor of MSP430 code can be run and tested, as if it was running on the actual chip. Hope that makes sence.