EmbeddedRelated.com
Imagine Conference

GPS and Barometric pressure sensor recommendation please

Started by Sonoman in comp.arch.embedded19 years ago 30 replies

Hi all: I am in the process of designing a project for school. This project requires a GPS sensor and a barometric pressure sensor to determine...

Hi all: I am in the process of designing a project for school. This project requires a GPS sensor and a barometric pressure sensor to determine position in space. I have not much knowledge about sensors yet but I am trying. I have spent several hours googling a few terms and so far I came up with the Garmin 18 GPS sensor, and I am still not sure which barometric pressure sensor I will u...


Ultrasonic Sensor Reciver Problem

Started by Dibyendu in comp.arch.embedded16 years ago 7 replies

Hi, I have built the ultrasonic sensor ranger with the help of "2002MAR08_RFD_DA_AN.PDF" but it is not working. Explanation of the...

Hi, I have built the ultrasonic sensor ranger with the help of "2002MAR08_RFD_DA_AN.PDF" but it is not working. Explanation of the sensor: Base on the availability of the component I choose, ( I ) 1. ICM7555 instead of TLC555 2. CA3130 instead of CA5160 and 3. LM567. 4. PIEZO ULTRASONIC SENSOR: Module T40-1601 R40-1601, Center...


Ultrasonic Sensor Receiver Problem

Started by Dibyendu in comp.arch.embedded16 years ago 3 replies

Hi, I have built the ultrasonic sensor ranger with the help of "2002MAR08_RFD_DA_AN.PDF" but it is not working. Explanation of the...

Hi, I have built the ultrasonic sensor ranger with the help of "2002MAR08_RFD_DA_AN.PDF" but it is not working. Explanation of the sensor: Base on the availability of the component I choose, ( I ) 1. ICM7555 instead of TLC555 2. CA3130 instead of CA5160 and 3. LM567. 4. PIEZO ULTRASONIC SENSOR: Module T40-1601 R40-1601, Center...


Ultrasonic Sensor

Started by Dibyendu in comp.arch.embedded16 years ago

Hi, I have built the ultrasonic sensor ranger with the help of http://www.eetasia.com/ARTICLES/2002MAR/2002MAR08_RFD_DA_AN.PDF but it is...

Hi, I have built the ultrasonic sensor ranger with the help of http://www.eetasia.com/ARTICLES/2002MAR/2002MAR08_RFD_DA_AN.PDF but it is not working. Explanation of the sensor: Base on the availability of the component I choose, ( I ) 1. ICM7555 instead of TLC555 2. CA3130 instead of CA5160 and 3. LM567. 4. PIEZO ULTRASONIC SENSOR: Module T40-1601 R40-1601, ...


Tapping signal from digital scale's weight sensor

Started by Cedi in comp.arch.embedded17 years ago 5 replies

Hi Group, I intend to make a weight aqcuistion digital system. For the sensor I bought commercial digital scale that have range 0-5kg with...

Hi Group, I intend to make a weight aqcuistion digital system. For the sensor I bought commercial digital scale that have range 0-5kg with 1gr resolution. (TANITA KD-403) After I opened the casing, I found that the load sensor and the processor connected by 4 wire: V+, V-, S+, and S- (this written on the pcb). I guessed that the sensor is strain gauge with bridge. So I did some research...


using a LED as a light sensor

Started by BrunoG in comp.arch.embedded17 years ago 81 replies

Hi, Here is an idea about using a LED as a light sensor, to dim a 7-segments LED display...

Hi, Here is an idea about using a LED as a light sensor, to dim a 7-segments LED display : http://www.micro-examples.com/public/microex-navig/doc/096-led-light-sensor.html Questions & comments are welcome ! Thanks, Bruno


CMOS sensor where to buy

Started by USB wcam in comp.arch.embedded14 years ago 1 reply

Where can I can find a CMOS sensor (ST, Omnivision, etc)with the lens, somebody sales the sensor with the lens ? ...

Where can I can find a CMOS sensor (ST, Omnivision, etc)with the lens, somebody sales the sensor with the lens ? --------------------------------------- This message was sent using the comp.arch.embedded web interface on http://www.EmbeddedRelated.com


(SPI equipped) Sensor Data to PC

Started by hhausen in comp.arch.embedded17 years ago 4 replies

Hello, I'm new in this group, and I hope this is the right one to place my question. I am trying to connect a tilt sensor to a pc. The sensor...

Hello, I'm new in this group, and I hope this is the right one to place my question. I am trying to connect a tilt sensor to a pc. The sensor device (Analog Devices' ADIS16201) is accessable via spi. Unfotunately, I'm not very conversant with programming Micros not even with programming serial communication. But since SPI is such a simple protocol I tried it using FTDI's FT2232C. That did no...


Problems with UART

Started by elsaximena in comp.arch.embedded18 years ago 2 replies

HI... I am programming with a MAVRIC II that uses the ATMEGA 128 but I connect GP2D12 infrarred sensor to the UART and I use the...

HI... I am programming with a MAVRIC II that uses the ATMEGA 128 but I connect GP2D12 infrarred sensor to the UART and I use the hyperterminal for see th output of the sensor but the only thing that I receive was: ??@}@@wp@}@pNstr@?????xw@????? What can I do??? The same thing happened with the srf04 ultrasoni sensor!!! I appreciate any help Thanks This message was sent us...


Help with OV7620 sensor connected to FPGA

Started by raul_ma in comp.arch.embedded14 years ago 2 replies

I'm trying to implement an OV7620 sensor on a Spartan 3 (Xilinx FPGA) to display on VGA, the problem is to syncronize the sensor data with...

I'm trying to implement an OV7620 sensor on a Spartan 3 (Xilinx FPGA) to display on VGA, the problem is to syncronize the sensor data with VGA exit. The sensor is already programed to send data in progressive mode by 2 channels: channel Y G G G G channel UV B R B R Please, somebody can tell me how to syncronize with a monitor to display data on VGA? Regards!!!


How To Drive and Read A 4-20mA Sensor

Started by eeboarder in comp.arch.embedded14 years ago 8 replies

Hello, I have limited experience with microcontrollers, all with freescale HC12 and HCS12 systems. I have dealt with 0-5V sensors through ADC...

Hello, I have limited experience with microcontrollers, all with freescale HC12 and HCS12 systems. I have dealt with 0-5V sensors through ADC before, too. I currently have a project where I might have to use a 4-20mA sensor. How would I go about electrically interfacing a 4-20mA sensor to a generic microcontroller? How would you power it and read it? Is there an IC available? Any suggest...


Low cost image sensor

Started by Anonymous in comp.arch.embedded18 years ago 4 replies

Hi, I have been searching the web for a low cost image sensor. The application is for reading a type of barcode, approximately 20mm x 5mm, but...

Hi, I have been searching the web for a low cost image sensor. The application is for reading a type of barcode, approximately 20mm x 5mm, but I could make do with an area as small as 10mm x 3mm. A resolution of 0.1mm would be more than adequate, and I only require monochrome. Ideally I would like no moving parts, and no lens. The item to be scanned would be placed directly on the sensor, il...


Image Sensor Interface

Started by pes in comp.arch.embedded16 years ago 3 replies

Hi, I' m looking for solutions to interface a 1.3Mpixels CMOS image sensor, I' ve thought to use a FPGA but it seems to be a little...

Hi, I' m looking for solutions to interface a 1.3Mpixels CMOS image sensor, I' ve thought to use a FPGA but it seems to be a little expensive. What about the market? Is there dedicated circuits to realize the interface and stock the data? Is there processors with DMA transfert which allow to interface the sensor? Thanks for your help.


1-25 m range sensor

Started by Ricardo Perezzo in comp.arch.embedded18 years ago 12 replies

What type of range (distance) measurement sensor (and/or sensor combinations to minimize the total cost) available with the following specs ...

What type of range (distance) measurement sensor (and/or sensor combinations to minimize the total cost) available with the following specs i. Range : 1-25 meters ii.Accuracy : 2-5cm iii. Max spot size at target : 10cm radius @ 25m iv. Repetation rate : 10Hz v. Price : (Yes, I would prefer "low cost" whatever it means)


image/sensor data routing and saving?

Started by solarst in comp.arch.embedded14 years ago 6 replies

Lots of questions, I hope someone can guide me in the right direction! I'm looking for some help in designing a system that can take data from...

Lots of questions, I hope someone can guide me in the right direction! I'm looking for some help in designing a system that can take data from an image sensor and store it in some sort of MMC/flash memory. It will be part of a wearable device for monitoring diet/activity constantly during the day. We're looking into using an image sensor from OmniVision that has built-in JPEG compression (e...


Sensor for Object detection

Started by Enoch in comp.arch.embedded14 years ago 1 reply

Hallo there Hi, I want to carry a research project on a sensor that can suitable to Detect an stable object. I would like to get an idea on how...

Hallo there Hi, I want to carry a research project on a sensor that can suitable to Detect an stable object. I would like to get an idea on how i can implement my project. I want to implement a sensor which can emit a ray or any kind of non hazadous emision which will respond to an object in a distance of one meter 1m then send the feedback to a board to produce an oscillating signal hence the ...


Baffled by Honeywell proximity sensor

Started by Anonymous in comp.arch.embedded19 years ago 6 replies

I've been given a sample Honeywell capacitative proximity sensor by a client. He wants me to build a small micro-based project to interface with...

I've been given a sample Honeywell capacitative proximity sensor by a client. He wants me to build a small micro-based project to interface with it. The sensor is shipped in a bag labeled "992AA12AN-A2", and the documentation for "992 series" sensors consists of four letter-sized sides, most of which are multilingual translations of warnings and mechanical specs. The electrical documentation ...


Need help in mplementing IoT protocols

Started by Anonymous in comp.arch.embedded6 years ago 1 reply

Hi.. I have a phynode sensor tag with cc2650 , one more phywave cc2650 radio module that supports zigbee, 6lowpan, ble, etc.. and a PHYGATE...

Hi.. I have a phynode sensor tag with cc2650 , one more phywave cc2650 radio module that supports zigbee, 6lowpan, ble, etc.. and a PHYGATE ,ARM335x gateway. I want to implement a IoT system for reading the sensor data and sending it to the cloud with the following requirements: Read the Sensor Data using : 1. BLE 2. 6LOWPAN 3. Zigbee 4. Lora Send the same info to the ...


OV9655 register config for raw data

Started by mbonamusa in comp.arch.embedded14 years ago 3 replies

Hello, I'm developing a camera with Omnivsion OV9655 image sensor. I want to use "raw RGB data" output format (bayer pattern). Which register...

Hello, I'm developing a camera with Omnivsion OV9655 image sensor. I want to use "raw RGB data" output format (bayer pattern). Which register configuration I have to do? I've read the sensor datasheet from omnivision, but I can't find the optimal register configuration. Someone can help me? Has anybody worked with this sensor? Thank you! --------------------------------------...


What Microcontroller can be used with inductive loop sensors

Started by simon86 in comp.arch.embedded15 years ago 5 replies

Hi, I am currently working on a university project that concerns the functionality of an inductive loop sensor. While I understand its...

Hi, I am currently working on a university project that concerns the functionality of an inductive loop sensor. While I understand its basic functionality I am unsure how to use it with microcontroller. We will be using the sensor to detect vehicles that are parked in a parking spot. Once detected, we want the sensor to communicate with some sort of microcontroller so a timer can be set. Ho...



Imagine Conference