Hi there, we have an ICE subsytem with the following pins: - CK (clock) - DO (data out) - DI (data in) - EN- (enable) - RST-...

Hi there, we have an ICE subsytem with the following pins: - CK (clock) - DO (data out) - DI (data in) - EN- (enable) - RST- (reset) The text in parentheses is our forecast meaning of the pin, while the uppercase acronyms are their names as reported in the (few) technical notes we have. Each pin has the "ICE" prefix, so we know this is a generic In-Circuit Emulator. The datashee...

Hello TO all guys I want to know that how to make a BSP ( Board support Packages ) for a new hardware using Linux kernel. I mean is there...

Hello TO all guys I want to know that how to make a BSP ( Board support Packages ) for a new hardware using Linux kernel. I mean is there any tutorial in regard with this topic. Also what are the basic requirements in order to move in this direction. Actually I want to practice it and want to test it on the virtual emulator like Qemu and than I will port it to my new hardware. ...

Hi I ask your help for a problem relative to my PC and its OS,but inherent to embedded electronics,because the problem affects just the debug...

Hi I ask your help for a problem relative to my PC and its OS,but inherent to embedded electronics,because the problem affects just the debug operations After a registry clean ,maybe done too deeply,my XP pro works fine except during debug: i have the same strange behaviour with two different IDE's, CodeWarrior for MCU 10.5 and LPCXpresso,r. 5.xx,6.xx Despite the USB emulator Debugger ...

I'm working with a very old 68360 based embedded system running from flash ROM based on pSOS+ RTOS, and need to debug. The BDM cannot do...

I'm working with a very old 68360 based embedded system running from flash ROM based on pSOS+ RTOS, and need to debug. The BDM cannot do hardware breakpoints while running from ROM and thus I'm looking for an emulator that may work with this. I've tried an old Mikrotek power-pack, but it's DOA upon boot, and am looking at what anyone may have around they no longer need. I don't have a bud...

Hello. We are in the beginning of development of new product with ARM7 Can someone tell us what options we have for development tools? We need...

Hello. We are in the beginning of development of new product with ARM7 Can someone tell us what options we have for development tools? We need a list of available dev toolset, such as compiler+emulator+(RTOS)+(dev. board)+(processor) that work with each other. also, perhaps some comments on those tools. Thanks!! Jack

I am attempting to write a command line interface for my embedded application (LM3S1439 based). I would like some advice on how to best approach...

I am attempting to write a command line interface for my embedded application (LM3S1439 based). I would like some advice on how to best approach it. Some of my specifications would be: -the CLI should communicate with any terminal emulator. -the backspace key should work as intended -other controls like arrow keys etc not necessary and should be ignored -the enter key delimits the command...

Greetings: For a change of pace (or a hands-on introduction to using an in-circuit emulator), please...

Greetings: For a change of pace (or a hands-on introduction to using an in-circuit emulator), please try: http://www.cybertheque.org/homebrew/hmi-200 Here you will have realtime access to ICE hardware and you can compile/assemble/execute/debug example code or your own code. Please try the DC-200Hz digital oscilloscope and my take on Tom Pittman's 1977 TinyBasic interpreter available...

How do I setup Code Composer Studio v2 to compile for the TMS320F2808? And how do I setup my XDS510PP PLUS JTAG Scan Path Emulator to work...

How do I setup Code Composer Studio v2 to compile for the TMS320F2808? And how do I setup my XDS510PP PLUS JTAG Scan Path Emulator to work with this DPS? I suspect that I must download a lot of updates?

Hi all, Do you know if there is a CAN (automotive network) stack under Linux ? Do you know if there is a CAN stack emulator / simulator /...

Hi all, Do you know if there is a CAN (automotive network) stack under Linux ? Do you know if there is a CAN stack emulator / simulator / analyser under Linux ? I need to experiment CAN under Linux. TIA & BR, Alain.

Hello, All! I started to use WindRiver JTAG emulator and supplied program visionCLICK 7.10a. And I faced with some issue. I have to prepare...

Hello, All! I started to use WindRiver JTAG emulator and supplied program visionCLICK 7.10a. And I faced with some issue. I have to prepare image for downloading to flash. I use convert utility from visionCLICK suite, actually I'm using GUI frontend for it. So, my input file is ELF format. Documentation is saying that I can specify range addresses for BIN image like: 0x00000000 to 0xf...

Hi all, I'm getting up to speed on the MSP430 with the ez340-Rf2500 dev kit, which connects to a pc via a USB-to-serial emulator. That is, the...

Hi all, I'm getting up to speed on the MSP430 with the ez340-Rf2500 dev kit, which connects to a pc via a USB-to-serial emulator. That is, the device is plugged into a USB port, but shows up as a COM port in Windows. For my application, I'd like this device to report real-time sensor data to the host computer, where it will be logged. I figure I should really have a serial port sniffer to ai...

After several intsruments built with the 6805, I'm looking to upgrade to a more modern processor with more code space and RAM, as well as more...

After several intsruments built with the 6805, I'm looking to upgrade to a more modern processor with more code space and RAM, as well as more modern debugging schemes. The 6808 series seems to fit the bill, specifically the GP32 chip. One of my biggest hangups about the 6805 is the ancient and poorly supported debugging/emulator tools (I use the Cosmic compiler which I DO like). After my ...

In all my embedded DSP based products I use an RS232 port (driven with printf) as a means of seeing whats going on inside a CPU or DSP. I am...

In all my embedded DSP based products I use an RS232 port (driven with printf) as a means of seeing whats going on inside a CPU or DSP. I am looking for a way to increase the flexability of the displayed data since there is often data from differnt processes all competing for my attention before it scrolls off the screen. I was considering using an X Windows terminal emulator program (whi...

Hi All, I would like to start a small project to woork on uClinux. I am searching for a board of ARM7 core and the full development...

Hi All, I would like to start a small project to woork on uClinux. I am searching for a board of ARM7 core and the full development environment. So please suggest me which board i have to purchase, JTAG emulator and development environment with debugger. As i am doing it on my own, i want to have all these things at the lowest cost possible. Even i m ready to rig up the circuits if the schemat...

For an existing motor control application, we're considering upgrading from our current ROMless ST10R167 processor to newer one with...

For an existing motor control application, we're considering upgrading from our current ROMless ST10R167 processor to newer one with onboard flash to get faster execution. One of the main attractions of the Infineon XC16X chips is JTAG debugging, with excellent code and onboard peripheral compatibility with the C167/ST10. (Using a bond-out emulator isn't practical with our equipment.) We use ...

Are there any commercial adaptors that would replace a floppy drive with some type of flash storage (sd, mmc, thumb drive)? To the host, this...

Are there any commercial adaptors that would replace a floppy drive with some type of flash storage (sd, mmc, thumb drive)? To the host, this would have to look just like the floppy drive it replaced, but use different media. The reason I ask is there are many old but useful embedded systems which have only the floppy for storage but no other interfaces (no IDE or USB).

Having developed a new IXP425 based card, we now face the problem of writing the BSP for it. Actually, the main problem at this very moment is...

Having developed a new IXP425 based card, we now face the problem of writing the BSP for it. Actually, the main problem at this very moment is understanding the real issues with Endianess. Indeed, primary tests made with the ARM MultiIce emulator appear to clearly indicate that Big Endian is required if wanting to access the IXP425 expansion bus with correct addressing (bytewise or wordw...

I've developed a nice business over the past 15 years lately using the 89lpc92x family of parts. The DIP (20) package is important so...

I've developed a nice business over the past 15 years lately using the 89lpc92x family of parts. The DIP (20) package is important so that upgrades may be made in the field. Yearly volume is 3-5K parts. Yes, boards are assembled by hand using through hole parts. I support 5 part timers and still use 51 assembler. About 15 active designs. I just blew the bondout R1.0 in my 2nd PDS900 and now hav...

Would anyone have seen a program for DOS which emulates an Epson graphics printer? I'm talking, you plug your output device (logic analyser as...

Would anyone have seen a program for DOS which emulates an Epson graphics printer? I'm talking, you plug your output device (logic analyser as is the case here) into a normal Epson printer via serial port, except in 2006 you don't have an Epson serial printer anymore. I'm sure this must have been done before somewhere. So a PC behaves as if it was a printer, and creates a .bmp file or ali...

Has anyone experienced having their JTAGICE firmware accidently erased? I hook up the emulator directly to my PC today with no target board. ...

Has anyone experienced having their JTAGICE firmware accidently erased? I hook up the emulator directly to my PC today with no target board. Then ran AVRProg.exe and erased. AVRProg.exe showed SUCCESS! Now the 200 dollar question is, how can I restore the firmware? I cannot do any debugging or ISP programming with my JTAGICE now! Thanks, Steven